En
AV RECEIVER
TX-NR5100
Instruction Manual
Contents
2
Reducing the Power Consumption in Standby
State
When the following functions are enabled, the power consumption in
standby state increases. To reduce the power consumption in standby state,
check each setting and set the functions to "O".
– HDMI CEC ( →p105)
– HDMI Standby Through ( →p105)
– USB Power Out at Standby ( →p112)
– Network Standby ( →p112)
– Bluetooth Wakeup ( →p113)
Table of contents
Detailed contents (Next page)
Firmware Update
Troubleshooting
Supplementary Information
Speaker ConnectionsSpeaker Connections
Zone BZone B
Main Room
Z
one
B
Zone B
Main Room
Roo
m
Speaker LayoutSpeaker Layout
3
Before starting the procedure 6
Firmware Update 7
Update Information of the rmware 7
Firmware Update Procedure 7
Part Names 10
Front Panel 10
Display 12
Rear Panel 13
Remote Controller 15
Inputting Characters 17
Speaker Layout
The listening room and the speaker layout 19
3.1 Channel System 20
5.1 Channel System 21
7.1 Channel System 22
3.1.2 Channel System 23
5.1.2 Channel System 24
Speaker Installation
Speaker Connections
Speakers you can use with this unit and cable
connections 31
Connections
Notes regarding connections with HDMI cables 45
Connections 45
Connecting the TV 46
To ARC/eARC TV 46
To Non-ARC TV 46
Connecting the SUB Monitor 47
SUB Monitor 47
Connecting Playback Devices 48
Connecting an AV Component with HDMI Jack 48
Connecting an Audio Component 49
Connecting an AV Component in a Separate Room
(ZONE B connection) 50
Connecting an Integrated Amplier (ZONE B) 50
Connecting Antennas 51
Network Connection 52
Connecting the Power Cord 53
Playback
Playing audio from an externally connected device 55
Basic Operations 55
BLUETOOTH
®
Playback 56
Playing audio from BLUETOOTH wireless technology
enabled devices with this unit 56
4
Transmitting audio from this unit to BLUETOOTH
wireless technology enabled devices 57
Listening To the Radio 59
Listening To the AM/FM Radio 59
Presetting a Radio Station 61
Listening Mode 62
Selecting a Listening mode 62
Quick Menu 64
Menu operations 64
Spotify 66
AirPlay
®
67
Basic Operations 67
Playing Back on multiple devices (AirPlay2) 68
DTS Play-Fi
®
69
Playing Back 69
Amazon Alexa 70
Registering this unit with an Amazon account 70
Operating this unit 71
Amazon Music 72
Registering This Unit with Amazon Music 72
Playing Amazon Music using the Onkyo Controller 73
Playing Amazon Music using the remote controller 73
TIDAL 74
Registering this unit with TIDAL 74
Playing TIDAL 74
Connecting the Sonos System for Playback 75
Necessary Equipment 75
How to Connect This Unit and Sonos Connect 75
Setting Up 75
Playing Sonos on This Unit 76
Internet Radio 77
Playing Back 77
Playing dierent audio and video 79
Displaying Your Favorite Video on TV While Playing
Music 79
USB Storage Device 80
Supported Audio Formats 80
USB Storage Device Requirements 80
Playing music les saved on a USB storage device 81
Music Server 83
Supported Audio Formats 83
Windows Media
®
Player 12 settings 83
Playing Back 84
Play Queue 86
Adding Play Queue Information 86
Sort and Delete 86
Playing Back 87
5
Connecting a transmitter for playback 88
Connections 88
Playing Back 88
Setup
Setup Menu 90
Menu list 90
1. Input/Output Assign 92
2. Speaker 96
3. Audio Adjust 101
4. Source 103
5. Hardware 105
6. Miscellaneous 114
Web Setup 116
Menu operations 116
Initial Setup with Auto Start-up Wizard 117
Operations 117
Onkyo Controller 120
Main features 120
Initial Setup 120
Troubleshooting
When the unit is operating erratically 123
Troubleshooting 124
Appendix
Speaker Layouts and Selectable Listening Modes 136
LISTENING MODE buttons and Selectable Listening
Modes 139
Input Formats and Selectable Listening Modes 141
Listening Mode Eects 145
Speaker combinations 150
General Specications 151
6
Before starting the procedure
What's in the box
1
2
5
34
1. Main unit (1)
2. Remote controller (RC-986R) (1), Batteries (AAA/R03) (2)
3. Speaker setup microphone (1)
• Used during Initial Setup.
4. Indoor FM antenna (1)
5. AM loop antenna (1)
• Initial Setup Guide (1)
* This is an online user manual. This is not supplied with the product.
Note
• Connect speakers with an impedance of 4 Ω to 16 Ω.
• The power cord must be connected only after all other connections are
completed.
• We will not accept any responsibility for damage arising from the connection
with equipment manufactured by other companies.
• Network services and content that can be used may no longer be available
if new functions are added by updating rmware or the service providers
terminate their services. Also, available services may dier depending on
your area.
• Details on the rmware update will be posted on our website and through
other means at a later date.
• Specications and appearance are subject to change without prior notice.
7
Firmware Update
This unit is equipped with a function to update the rmware via network or USB
port when the rmware update is announced after purchase. This enables
various functions to be added and operations to be improved.
Depending on the manufacturing timing of the product, the rmware may be
switched to the updated one. In such a case, new functions may be added
from the start. For how to conrm the latest rmware contents and the rmware
version of your product, see the following section.
Update Information of the rmware
For the latest rmware contents and the rmware version, visit our company's
website. If the rmware version of your product diers from the latest one, it is
recommended to update the rmware.
To conrm the rmware version of your product, press the button on the
remote controller, and refer to "6. Miscellaneous" - "Firmware Update" -
"Version" ( →p115).
Firmware Update Procedure
The update may take approx. 20 minutes to complete via network or via USB
port. Existing settings are guaranteed in either updating method.
When this unit is connected to the network, notications of rmware updates
may be displayed. To update the rmware, select "Update Now" with the cursor
buttons of the remote controller and press ENTER. The unit automatically enters
standby mode after "Completed!" is displayed, and the update is completed.
Disclaimer: The program and accompanying online documentation are
furnished to you for use at your own risk.
Our company will not be liable and you will have no remedy for damages for
any claim of any kind whatsoever concerning your use of the program or the
accompanying online documentation, regardless of legal theory, and whether
arising in tort or contract.
In no event will our company be liable to you or any third party for any special,
indirect, incidental, or consequential damages of any kind, including, but not
limited to, compensation, reimbursement or damages on account of the loss of
present or prospective prots, loss of data, or for any other reason whatsoever.
Updating the Firmware via Network
• While updating the rmware, do not do the following:
– Disconnecting and reconnecting cables, USB storage device, speaker
setup microphone or headphones, or performing operations on the unit
such as turning the power o
– Accessing this unit from a PC or smartphone using their applications
• Check that the unit is turned on, and the connection to the Internet is secured.
• Turn o control devices (PC etc.) connected to the network.
• Stop an Internet radio, USB storage device, or server content being played.
• If "HDMI CEC" is set to "On", set it to "O".
– Press . Next, select "5. Hardware" - "HDMI" and press ENTER, then
select "HDMI CEC" and select "O".
* The descriptions may dier from the actual on-screen displays, however, operations
and functions are the same.
Update
1. Press .
The Setup menu is displayed on the TV screen.
2. Select "6. Miscellaneous" - "Firmware Update" - "Update via NET" with the
cursors in order, then press ENTER.
• If "Firmware Update" is grayed out and cannot be selected, wait for a while
until it starts up.
• If there is no updatable rmware, "Update via NET" cannot be selected.
3. Press ENTER with "Update" selected, and start update.
• During the update, the TV screen may go black depending on the program
to be updated. In such a case, check the progress on the display of the
unit. The TV screen will remain black until the update is completed and the
power is turned on again.
• When "Completed!" is displayed, the update is complete.
4. Press ON/STANDBY on the main unit to turn the unit into standby mode.
The process is completed, and your rmware is updated to the latest version.
• Do not use on the remote controller.
If an Error Message is Displayed
• If an error occurs, "- Error!" is displayed on the display of the unit. (""
represents an alphanumeric character.) Refer to the following descriptions
8
and check.
Error Code
• -01, -10:
Ethernet cable not found. Connect the Ethernet cable properly.
• -02, -03, -04, -05, -06, -11, -13, -14, -16, -17, -18, -20,
-21:
Internet connection error. Check the following:
– Whether the router is turned on
– Whether this unit and the router are connected via the network
Unplug and plug the power cords of this unit and the router. This may solve
the problem. If you are still unable to connect to the Internet, the DNS server
or proxy server may be temporarily down. Check the server operation status
with your Internet service provider.
• Others:
After removing the power plug once, insert it to the outlet, and then start the
operation from the beginning.
Updating via USB
• While updating the rmware, do not do the following:
– Disconnecting and reconnecting cables, USB storage device, speaker
setup microphone or headphones, or performing operations on the unit
such as turning the power o
– Accessing this unit from a PC or smartphone using their applications
• Prepare a 1 GB or larger USB storage device. The format of USB storage
devices supports FAT16 or FAT32 le system format.
– Media inserted into a USB card reader may not be used for this function.
– USB storage devices equipped with the security function are not
supported.
– USB hubs and USB devices equipped with the hub function are not
supported. Do not connect these devices to the unit.
• Delete any data stored on the USB storage device.
• Turn o control devices (PC etc.) connected to the network.
• Stop an Internet radio, USB storage device, or server content being played.
• If "HDMI CEC" is set to "On", set it to "O".
– Press . Next, select "5. Hardware" - "HDMI" and press ENTER, then
select "HDMI CEC" and select "O".
* Depending on the USB storage device or its content, long time may be required
for loading, the content may not be loaded correctly, or power may not be supplied
correctly.
* Our company will not be liable whatsoever for any loss or damage of data, or
storage failure arising from the use of the USB storage device. Please note this in
advance.
* The descriptions may dier from the actual on-screen displays, however, operations
and functions are the same.
Update
1. Connect the USB storage device to your PC.
2. Download the rmware le from the our company's website to your PC and
unzip.
Firmware les are named as below.
ONKAVR_R.zip
Unzip the le on your PC. The number of unzipped les and folders varies
depending on the model.
3. Copy all unzipped les and folders to the root folder of the USB storage
device.
• Make sure to copy the unzipped les.
9
4. Connect the USB storage device to the USB port of this unit.
• If an AC adapter is supplied with the USB storage device, connect the AC
adapter, and use it with a household outlet.
• If the USB storage device has been partitioned, each section will be
treated as an independent device.
5. Press .
The Setup menu is displayed on the TV screen.
6. Select "6. Miscellaneous" - "Firmware Update" - "Update via USB" with the
cursors in order, then press ENTER.
• If "Firmware Update" is grayed out and cannot be selected, wait for a while
until it starts up.
• If there is no updatable rmware, "Update via USB" cannot be selected.
7. Press ENTER with "Update" selected, and start update.
• During the update, the TV screen may go black depending on the program
to be updated. In such a case, check the progress on the display of the
unit. The TV screen will remain black until the update is completed and the
power is turned on again.
• During the update, do not turn the power o, or disconnect or reconnect
the USB storage device.
• When "Completed!" is displayed, the update is complete.
8. Disconnect the USB storage device from the unit.
9. Press ON/STANDBY on the main unit to turn the unit into standby mode.
The process is completed, and your rmware is updated to the latest version.
• Do not use on the remote controller.
If an Error Message is Displayed
If an error occurs, "- Error!" is displayed on the display of the unit. (""
represents an alphanumeric character.) Refer to the following descriptions and
check.
Error Code
• -01, -10:
The USB storage device cannot be recognized. Check if the USB storage
device or USB cable is securely inserted to the USB port of the unit.
Connect the USB storage device to an external power source if it has its own
power supply.
• -05, -13, -20, -21:
The rmware le is not present in the root folder of the USB storage device,
or the rmware le is for another model. Retry from the download of the
rmware le.
• Others:
After removing the power plug once, insert it to the outlet, and then start the
operation from the beginning.
10
Part Names
Front Panel
12
345678 9J
KL
1. ON/STANDBY button
2. PURE AUDIO button/indicator: Switches to the
Pure Audio mode. The indicator lights when the
mode is on. ( →p148)
3. HYBRID STANDBY indicator: Lights up when
any of the following functions is working or
enabled in standby state of this unit. When this
indicator is lighting, the power consumption in
standby state increases, however, the increase
in power consumption is minimized by entering
the HYBRID STANDBY mode where only the
essential circuits operate.
– HDMI CEC ( →p105)
– HDMI Standby Through ( →p105)
– USB Power Out at Standby ( →p112)
– Network Standby ( →p112)
– Bluetooth Wakeup ( →p113)
4. Remote control sensor: Receives signals from
the remote controller.
• The reception range of the remote controller
is within a distance of approx. 16´/5 m, and
an angle of 20° in vertical direction and 30° to
right and left.
5. ZONE A/B button: Selects an audio output
destination. ( →p88)
6. INFO button: Switches the information on the
display.
7. QUICK MENU button: Pressing this button
during playback can make settings such as
"HDMI" and "Audio" quickly on the TV screen
while playing. ( →p64)
8. Display ( →p12)
9. SETUP button: You can display advanced
setting items on the TV and the display to have
a more enjoyable experience with this unit.
( →p89)
10.
Cursor buttons ( / / / ) and ENTER
button: Select an item with the cursors, and
press ENTER to conrm your selection. When
using TUNER, use them to tune in to stations.
( →p59)
11.
RETURN button: Returns the display to the
previous state while setting
12.
MASTER VOLUME
11
Front Panel
MN PQ
O
13.
PHONES jack: Connect headphones with a
standard plug (ø1/4″/6.3 mm).
14.
LISTENING MODE button: Switches the
listening mode ( →p62) by pressing "MOVIE/
TV", "MUSIC" and "GAME" repeatedly.
15.
Input selector buttons: Switches the input to be
played.
16.
TONE CONTROL button: Adjusts the sound
quality. Press / of "TREBLE", "VOCAL" or
"BASS" respectively.
17.
SETUP MIC jack: Connect the supplied speaker
setup microphone. ( →p119)
12
Display
12
76 7
34
5
1. Speaker/Channel display: Displays the output
channel that corresponds to the selected
listening mode.
2. Lights in the following conditions.
: Headphones are connected.
: Connected by BLUETOOTH.
: Connected by Wi-Fi.
NET: Lights when connected to the network with
the "NET" input selector. It will blink if incorrectly
connected to the network.
USB: Lights when the "NET" input selector is
selected, a USB device is connected and the
USB input is selected. It will blink if the USB
device is not properly connected.
HDMI: HDMI signals are input and the HDMI
input is selected.
DIGITAL: Digital signals are input and the digital
input is selected.
A: Audio is output only to ZONE A.
B: Audio is output only to ZONE B.
AB: Audio is output to both ZONE A and ZONE
B.
3. Lights according to the type of input digital audio
signal and the listening mode.
4. Lights in the following conditions.
TUNED: Receiving AM/FM radio.
FM ST: Receiving FM stereo.
SLEEP: Sleep timer is set.
AUTO STBY: Auto Standby is set. ( →p112)
5. Blinks when muting is on.
6. Displays various information of the input signals.
7. Cursors ( / / / ): These may light when
performing operations while "NET" is selected
with the input selector. / light when there are
multiple folders or les that are available to be
selected. / light when text information does
not t with the range provided by "6".
13
Rear Panel
12
345674
8
1. DIGITAL IN OPTICAL/COAXIAL jacks: Input
TV or AV component digital audio signals with a
digital optical cable or digital coaxial cable.
2. TUNER AM/FM terminal: Connect the supplied
antennas.
3. HDMI OUT jacks: Transmit video signals and
audio signals with an HDMI cable connected to a
monitor such as a TV or projector.
4. Wireless antenna: Used for WI-Fi connection or
when using a BLUETOOTH
enabled device. Adjust the
angles according to the
connection status.
5. HDMI IN jacks: Transmit video signals and audio
signals with an HDMI cable connected to an AV
component.
6. ETHERNET port: Connect to the network with
an Ethernet cable.
7. USB port: Connect a USB storage device to
play music les ( →p80). You can also supply
power (5 V/1 A) to USB devices with a USB
cable.
8. Power cord
180°
90°
14
Rear Panel
9JKL
9.
AUDIO IN jacks: Input AV component audio
signals with an analog audio cable.
10.
ZONE B PRE/LINE OUT jacks: Simultaneously
output the same audio source as the speakers
(ZONE A) connected to this unit by connecting
this unit to wireless headphones, wireless
speaker transmitter, etc., using an analog audio
cable.
11.
SUBWOOFER PRE OUT jacks: Connect a
powered subwoofer with a subwoofer cable.
Up to two powered subwoofers can be
connected. The same signal is output from each
SUBWOOFER PRE OUT jack.
12.
SPEAKERS terminals: Connect speakers with
speaker cables. (FRONT L/R terminals support
banana plugs. Use a plug 4 mm in diameter.
Y plug connection is not supported.)
15
Remote Controller
1. ON/STANDBY button
2. Input selector buttons: Switches the input to be
played.
3. Play buttons: Used for playback operations
for the Music Server ( →p83) or USB device
( →p80). Also, switching to "CEC MODE"
with "18. MODE button" allows you to operate
an HDMI CEC function-enabled AV component.
(Some devices may not be operated.)
4. Q (QUICK MENU) button: Pressing this button
during playback allows you to make settings
such as "HDMI" and "Audio" quickly on the TV
screen while playing. ( →p64)
5. Cursor buttons and ENTER button: Select
an item with the cursors, and press ENTER to
conrm your selection. Pressing / button
allows you to switch the screen when a music
folder list or le list is not displayed on one
screen on the TV.
6. button: Displays advanced setting items on
the TV or the display to have a more enjoyable
experience with this unit. ( →p89)
7. SLEEP button: You can allow the unit to enter
standby automatically when the specied time
has elapsed. Select the time from "30 min",
"60 min", "90 min" and "O". When you do not
want to turn the unit to standby automatically,
select "O". You can also set this by pressing
button and selecting "5. Hardware" - "Power
Management" - "Sleep Timer" ( →p112) on the
Setup menu.
8. HDMI MAIN/SUB button: Select the HDMI OUT
jack to output video signals from "MAIN", "SUB",
and "MAIN+SUB".
9. button: Switches the information on the
display. Also, when the "BLUETOOTH" input
selector is selected, pressing and holding this
button for 5 seconds or more will switch to the
pairing mode.
10.
button: Returns the display to the previous
state while setting.
11.
MUTE button: Temporarily mutes audio.
Press the button again to cancel muting.
1
7
8
9
J
K
2
3
4
5
6
16
Remote Controller
12.
TONE buttons: Adjusts the sound quality. Press
"TREBLE", "BASS", or "VOCAL" to select what
you want to adjust, then adjust with + and -.
TREBLE/BASS button: You can adjust the
sound quality of the front speakers.
1. Press TREBLE or BASS to select the content
to adjust.
TREBLE: Enhances or moderates the high-
tone range of the front speakers.
BASS: Enhances or moderates the low-tone
range of the front speakers.
2. Press + or - to adjust.
VOCAL button: Emphasizes movie dialogues
and music vocals to listen to them more easily.
It is eective to movie lines in particular. Also, it
exerts the eect even if the center speaker is not
used. Select a desired level from "1" (low) to "5"
(high).
1. Press VOCAL.
2. Press + or - to adjust.
• Depending on the input source or listening
mode setting, selection is not possible, or the
desired eect may not be achieved.
13.
LISTENING MODE buttons: Selects a listening
mode ( →p62, p139).
14.
DIMMER button: Switches the brightness of the
display with three levels. It cannot be turned o
completely.
15.
VOLUME buttons
16.
CLEAR button: Deletes all characters you have
entered when entering text on the TV screen.
17.
MEMORY button: Used to register AM/FM radio
stations. ( →p61)
18.
MODE button: Switches between automatic
tuning and manual tuning for AM/FM stations
( →p59). Also, when an HDMI CEC function-
enabled AV component is connected to this unit,
you can switch "3. Play buttons" between "CEC
MODE" and "RCV MODE" (normal mode).
L
M
N
O
P
Q
R
17
Inputting Characters
You can input characters or symbols on the keyboard displayed on the TV
screen such as when inputting a password for Wi-Fi Setup ( →p107) or naming
a preset radio station ( →p103).
1. Select a character or symbol with the cursors / / / on the remote
controller and press the ENTER button.
2. When saving characters after input, select "OK" and press the ENTER button.
, . ;/ : ], . ; :
CLEAR
MODE
/ / /
ENTER
• Select "A/a" to switch between upper and lower cases. (Can also be switched
with the MODE button on the remote controller.)
• To enter a space, select " ".
• To delete a character on the left of the cursor, select " ".
• To delete all the input characters, press the CLEAR button on the remote
control.
Speaker Layout
7.1ch
3.1.2ch
5.1.2ch
3.1ch
5.1ch
18
Speaker Layout
Speaker Layout
This unit can be used in dierent ways, depending on the layout of the
speakers you are installing. Select the speaker layout that suits the installation
environment, then conrm the methods for installation and connection.
Speaker Layout
Speaker layout ( →p20)
Speaker Installation ( →p25)
Speaker Connections ( →p30)
Speaker Combinations ( →p150)
7.1ch
3.1.2ch
5.1.2ch
3.1ch
5.1ch
19
Speaker Layout
The listening room and the speaker layout
1
2
1. ZONE A Speakers
The speaker system set up in the main room (where this unit is located).
2. ZONE B Speakers
The 2 ch speaker system set up in a separate room (ZONE B). The same source
can be played back in the main room and the separate room simultaneously.
ZONE A
(Main Room)
ZONE B
5.1ch
7.1ch
3.1.2ch
5.1.2ch
3.1ch
23
Speaker Layout
3.1.2 Channel System
A Speaker System that is a 3.1 Channel System with one set of height speakers added.
3.1.2 ch (Front High or Rear High) ( →p28) 3.1.2 ch (Top Front or Top Middle or Top Rear)
( →p28)
3.1.2 ch (Dolby Enabled Speakers (Front))
( →p28)
Zone BZone B
Main Room
3.1.2 ch + ZONE B ( →p28) 3.1.2 ch (Bi-Amping (Front)) ( →p28)
5.1ch
7.1ch
3.1.2ch
5.1.2ch
3.1ch
24
Speaker Layout
5.1.2 Channel System
A Speaker System that is a 5.1 Channel System with one set of height speakers added.
5.1.2 ch (Front High or Rear High) ( →p29) 5.1.2 ch (Top Front or Top Middle or Top Rear)
( →p29)
5.1.2 ch (Dolby Enabled Speakers (Front or
Surround)) ( →p29)
Speaker Installation
5.1ch
7.1ch
3.1.2ch
5.1.2ch
3.1ch
25
Speaker Installation
Speaker Installation
How the speakers are set up depends on the size and shape of the room, so
here we introduce just a basic layout example.
The alphabetic symbols used in this chapter represent the following speakers:
FL Front speaker Left
FR Front speaker Right
C Center speaker
SW powered SubWoofer
SL Surround speaker Left
SR Surround speaker Right
SBL Surround Back speaker Left
SBR Surround Back speaker Right
FHL Front High speaker Left
FHR Front High speaker Right
RHL Rear High speaker Left
RHR Rear High speaker Right
TFL Top Front speaker Left
TFR Top Front speaker Right
TML Top Middle speaker Left
TMR Top Middle speaker Right
TRL Top Rear speaker Left
TRR Top Rear speaker Right
DFL Dolby enabled speaker Front Left
DFR Dolby enabled speaker Front Right
DSL Dolby enabled speaker Surround Left
DSR Dolby enabled speaker Surround Right
Speaker Installation
7.1ch
3.1.2ch
5.1.2ch
3.1ch
5.1ch
26
Speaker Installation
3.1 Channel System
a
FL FR
C
SW
a: 22° to 30°
FL, FR Place the Left and Right Front Speakers to match ear height.
C The center speaker should be set up facing the listening position at
an angle.
SW Place the powered subwoofer between the center speaker and a
front speaker.
3.1 ch connection ( →p33)
3.1 ch + ZONE B connection ( →p34)
3.1 ch (Bi-Amping (Front)) connection ( →p35)
5.1 Channel System
b
a
FL FR
SL SR
C
SW
a: 22° to 30°, b: 120°
FL, FR Place the Left and Right Front Speakers to match ear height.
C The center speaker should be set up facing the listening position
at an angle.
SW Place the powered subwoofer between the center speaker and a
front speaker.
SL, SR Place the Left and Right Surround Speakers to be just above ear
height.
5.1 ch connection ( →p36)
5.1 ch + ZONE B connection ( →p37)
5.1 ch (Bi-Amping (Front)) connection ( →p38)
3.1.2ch
5.1.2ch
3.1ch
5.1ch
7.1ch
27
Speaker Installation
7.1 Channel System
b
c
a
FL FR
C
SW
SL SR
SBL SBR
a: 22° to 30°, b: 90° to 110°, c: 135° to 150°
FL, FR Place the Left and Right Front Speakers to match ear height.
C The center speaker should be set up facing the listening position at
an angle.
SW Place the powered subwoofer between the center speaker and a
front speaker.
SL, SR Place the Left and Right Surround Speakers to be just above ear
height.
SBL, SBR Place the Left and Right Surround Back Speakers at ear height.
• If surround back speakers are installed, be sure to install surround speakers
as well.
7.1 ch connection ( →p39)
5.1ch
7.1ch
3.1.2ch
5.1.2ch
3.1ch
28
Speaker Installation
3.1.2 Channel System
High Speakers
a
FHL FHR
RHL RHR
3´ (0.9 m)
or more
3´ (0.9 m)
or more
a: 22° to 30°
FHL, FHR Place the front high speakers directly above the front speakers,
angled to face the listening position.
RHL, RHR Place the rear high speakers so the lateral distance matches the
front speakers, angled to face the listening position.
3.1.2 ch connection ( →p40)
3.1.2 ch + ZONE B connection ( →p41)
3.1.2 ch (Bi-Amping (Front)) connection ( →p42)
Top Speakers
TFL
TFR
TML
TMR
TRL
TRR
a
b
c
a: 30° to 55°
b: 65° to 100°
c: 125° to 150°
TFL, TFR
Fit top front speakers on the ceiling in front of the listening position.
TML, TMR Fit top middle speakers on the ceiling directly above the listening
position.
TRL, TRR Fit top rear speakers on the ceiling behind the listening position.
• Match the lateral distance of the top speakers to the front speakers.
Dolby Enabled Speakers
a: 22° to 30°
a
DFL DFR
DFL, DFR The Dolby enabled speakers (front) are installed on top of the
front speakers.
5.1ch
7.1ch
3.1.2ch
5.1.2ch
3.1ch
29
Speaker Installation
5.1.2 Channel System
High Speakers
b
FHL FHR
RHL RHR
a
a: 22° to 30°
b: 120°
3´ (0.9 m)
or more
3´ (0.9 m)
or more
FHL, FHR Place the front high speakers directly above the front speakers,
angled to face the listening position.
RHL, RHR Place the rear high speakers so the lateral distance matches the
front speakers, angled to face the listening position.
5.1.2 ch connection ( →p43)
Top Speakers
TFL
TFR
TML
TMR
TRL
TRR
a
b
c
a: 30° to 55°
b: 65° to 100°
c: 125° to 150°
TFL, TFR
Fit top front speakers on the ceiling in front of the listening position.
TML, TMR Fit top middle speakers on the ceiling directly above the listening
position.
TRL, TRR Fit top rear speakers on the ceiling behind the listening position.
• Match the lateral distance of the top speakers to the front speakers.
Dolby Enabled Speakers
b
a
DFL DFR
DSL DSR
a: 22° to 30°
b: 120°
DFL, DFR The Dolby enabled speakers (front) are installed on top of the
front speakers.
DSL, DSR The Dolby enabled speakers (surround) are installed on top of the
surround speakers.
Speaker Connections
5.1ch
7.1ch
3.1.2ch
5.1.2ch
3.1ch
30
Speaker Connections
Speaker Connections
(Before starting the procedure)
Speakers you can use with this unit and cable
connections 31
4-16Ω
3.1 Channel System 33, 34, 35
5.1 Channel System 36, 37, 38
7.1 Channel System 39
3.1.2 Channel System 40, 41, 42
5.1.2 Channel System 43
Speaker Connections
5.1ch
7.1ch
3.1.2ch
5.1.2ch
3.1ch
31
Speaker Connections
Speakers you can use with this unit and cable connections
Connections
(Note) Speaker Impedance
Connect speakers with an impedance of 4 Ω to 16 Ω. If any of the speakers to be connected has an impedance of 4 Ω or more and less than 6 Ω, set "Speaker
Impedance" to "4ohms" for "Speaker Setup" in the Initial Setup section ( →p117). When setting "Speaker Impedance" from the Setup menu, press on the remote
controller, and set "2. Speaker" - "Conguration" - "Speaker Impedance" ( →p96) to "4ohms".
Connect the Speaker Cables
1/2˝
(12 mm)
Make correct connection between the unit's jacks and speaker's jacks (+ side to + side, and - side to - side) for each channel. If the connection is wrong, a bass
sound will not be reproduced properly due to reverse phase. Twist the wires exposed from the tip of the speaker cable so that the wires do not stick out of the
speaker terminal when connecting. If the exposed wires touch the rear panel, or the + side and – side wires touch each other, a malfunction may occur.
5.1ch
7.1ch
3.1.2ch
5.1.2ch
3.1ch
35
Speaker Connections
3.1 Channel System (Bi-Amping the Speakers)
FL FR
C
SW
SW CFR FL
For high-
frequency
For low-
frequency
Be sure to remove the jumper bar connecting between the woofer jacks and tweeter jacks of the Bi-Amping supported speakers. Refer to the instruction manual of
your speakers as well.
5.1ch
7.1ch
3.1.2ch
5.1.2ch
3.1ch
38
Speaker Connections
5.1 Channel System (Bi-Amping the Speakers)
SL SR
C
SW
FL FR
SW
SR SLC
FR FL
For high-
frequency
For low-
frequency
Be sure to remove the jumper bar connecting between the woofer jacks and tweeter jacks of the Bi-Amping supported speakers. Refer to the instruction manual of
your speakers as well.
5.1ch
7.1ch
3.1.2ch
5.1.2ch
3.1ch
42
Speaker Connections
3.1.2 Channel System (Bi-Amping the Speakers)
HL HR
C
SW
FL FR
HR
OR
OR
HL
OR
OR
SW CFR FL
For high-
frequency
For low-
frequency
Be sure to remove the jumper bar connecting between the woofer jacks and tweeter jacks of the Bi-Amping supported speakers. Refer to the instruction manual of
your speakers as well.
*1 Connect the Height Speakers you have actually installed (HL/HR: Height Speakers, Top Speakers, Dolby Enabled Speakers).
*1
Connections
44
Connections
Connections
Notes regarding connections with HDMI cables 45
Connecting the TV 46
Connecting the SUB Monitor 47
Connecting Playback Devices 48
Connecting an AV Component in a Separate Room
(ZONE B connection) 50
Connecting Antennas 51
Network Connection 52
Connecting the Power Cord 53
Connections
45
Connections
Notes regarding connections with HDMI cables
HDMI (High-Denition Multimedia Interface) is a digital interface standard for
connecting TVs, projectors, Blu-ray Disc players, game consoles, and other
video components. With HDMI, a single cable can carry control signals, digital
video, and digital audio.
Connections
Push HDMI cables straight in and all the way. You can damage the terminals if
you try to insert at an angle.
Right
Wrong
Right Wrong
• Hold the terminal housing on the HDMI cable when unplugging. Pulling on the
cable may lead to damaged cabling.
(Note) Placement of cables
Putting a load on HDMI cables can lead to poor operational performance. Place
the cables so there is no load put on them.
Right Wrong Wrong
• When 4K high-quality video (4K 60Hz, 4K HDR, etc.) is to be played, use
Premium High Speed HDMI Cable or Premium High Speed HDMI Cable
with Ethernet that have the "PREMIUM Certied Cable" label attached to the
packaging.
• When 8K high-quality video (8K 60Hz, etc.) is to be played, use ULTRA High
Speed HDMI Cable that has the "ULTRA HIGH SPEED" label attached to the
packaging.
46
Connections
Connecting the TV
By connecting a TV to this unit, you can show the video from AV devices connected to this unit on the TV and also play the sound from the TV through this unit.
DIGITAL
OPTICAL
OUT
IN(ARC)
a
b
To ARC/eARC TV
If the TV supports the ARC (Audio Return Channel) function(*), use only the
HDMI cable to connect with the TV. Use the ARC-compatible HDMI IN jack of
the TV for connection. You connect the HDMI cable to the HDMI OUT MAIN jack
labeled "ARC" on the receiver side.
• When a TV compatible with the eARC function is connected, use an HDMI
cable that supports Ethernet.
To Non-ARC TV
If the TV does not support the ARC (Audio Return Channel) function(*), connect
an HDMI cable and digital optical cable.
• If you use a cable set-top box, etc. connected to the input jack of this unit to
watch TV (without using a built-in tuner of the TV), connection with a digital
optical cable is not required.
Setup
• When not using the ARC function, press on the remote controller, then
set "5. Hardware" - "HDMI" - "Audio Return Channel (eARC supported)"
( →p106) to "O".
(*)The ARC function and eARC function transmit the audio signals of the TV via
an HDMI cable, and plays the audio of the TV on this unit. To check if the TV
supports the ARC function and eARC function, refer to the instruction manual
of the TV, etc.
ARC/eARC compatible audio formats ( →p153)
• Settings are required when 4K or 8K high-quality video is to be played.
Refer to "HDMI 4K/8K Signal Format" ( →p93) for information on the
settings. Also, use an HDMI cable that supports 4K or 8K video.
TV
ARC TV
Non-ARC TV
SUB Monitor ( →p47)
Be sure to insert the HDMI
cable all the way in.
a HDMI cable, b Digital optical cable
47
Connections
a
SUB Monitor
SUB Monitor
This unit has multiple HDMI OUT jacks, and another TV or projector can be
connected to the HDMI OUT SUB jack.
• Switch between MAIN and SUB using the HDMI MAIN/SUB button on the
remote controller ( →p15) or "Quick Menu" ( →p64). Note that this jack
is not ARC-compatible.
• If devices with dierent resolutions are connected to HDMI OUT MAIN jack
and SUB jack, images are output with the lower resolution.
Connecting the SUB Monitor
Be sure to insert the HDMI
cable all the way in.
a HDMI cable
48
Connections
Connecting Playback Devices
Connecting an AV Component with HDMI Jack
This is a connection example of an AV component equipped with an HDMI jack.
When connecting with an AV component that conforms to the CEC (Consumer
Electronics Control) standard, you can use the HDMI CEC function (*) that
enables linking with input selectors, etc. and the HDMI Standby Through
function that can transmit video and audio signals of the AV component to the
TV even if this unit is in standby mode.
• Settings are required when 4K or 8K high-quality video is to be played.
Refer to "HDMI 4K/8K Signal Format" ( →p93) for information on the
settings. Also, use an HDMI cable that supports 4K or 8K video.
• The corresponding resolution is dierent depending on the HDMI jack
connected. See "Supported input resolutions" ( →p154) for details.
• To enjoy digital surround sound including Dolby Digital, set the audio output of
the connected Blu-ray Disc player etc. to the Bitstream output.
(*)The HDMI CEC function: This function enables various linking operations with
CEC-compliant devices, such as switching input selectors interlocking with
a CEC-compliant player, switching audio output between TV and this unit or
adjusting the volume using the remote controller of a CEC-compliant TV, and
automatically switching this unit to standby when the TV is turned o.
a HDMI cable
GAME
BD/DVD Cable/Satellite
set-top box
a
Be sure to insert the HDMI
cable all the way in.
50
Connections
Connecting an AV Component in a Separate Room (ZONE B connection)
Connecting an Integrated Amplier (ZONE B)
While performing playback in the main room (where this unit is located), you can
enjoy 2-ch audio of the same source in the separate room (ZONE B) at the same
time. Use an analog audio cable to connect the ZONE B PRE/LINE OUT jack of
this unit to the LINE IN jack of the integrated amplier or power amplier in the
separate room.
Setup
• When connecting the power amplier, set "Zone B Output Level" to "Variable"
for "Speaker Setup" in the Initial Setup section ( →p117). When setting
"Zone B Output Level" from the Setup menu, press on the remote
controller, and set "2. Speaker" - "Conguration" - "Zone B Output Level"
( →p96) to "Variable". If it is not set, a large volume is output and the power
amplier, speakers, etc. may be damaged.
a
Input
Terminal
Integrated
amplier
a Analog audio cable
52
Connections
Network Connection
This unit can be connected to the network using a wired LAN or Wi-Fi (wireless
LAN). You can enjoy network functions such as Internet radio by network
connection. If connection is made by the wired LAN, connect the router and the
ETHERNET jack with the Ethernet cable as shown in the illustration. To connect
by Wi-Fi, select your desired setting method in "Network Connection" ( →p118)
of Initial Setup, and then follow the on-screen instructions. To congure the
setting on the Setup menu after the completion of Initial Setup, press the
button on the remote controller, and select "5. Hardware" - "Network" to make
the setting ( →p107). For the Wi-Fi connection, stand the wireless antenna for
use.
a
a Ethernet cable
Playback
54
Playback
Basic Operations
Playing audio from an externally connected device 55
BLUETOOTH
®
Playback 56
Listening To the Radio 59
Listening Mode 62
Quick Menu 64
Network Service
Spotify 66
AirPlay
®
67
DTS Play-Fi
®
69
Amazon Alexa 70
Amazon Music 72
Connecting the Sonos System for Playback 75
Internet Radio 77
Convenience functions
Playing dierent audio and video 79
USB Storage Device 80
Music Server 83
Play Queue 86
Connecting a transmitter for playback 88
Playback
55
Playback
Playing audio from an externally connected device
You can play the audio from AV components, such as Blu-ray disc players through this unit.
• When a TV is connected to the HDMI OUT SUB jack, use the HDMI MAIN/SUB button or "Quick Menu" ( →p64) to switch between MAIN and SUB.
Basic Operations
Perform the following procedure when this unit is on.
1. Switch the input on the TV to the input connected to the unit.
2. Press the input selector whose name is the same as that of the jack to which
the player is connected.
For example, press BD/DVD to play the player connected to the BD/DVD
jack. Press TV to listen to the sound of the TV.
• When the CEC link function works, the input switches automatically
when a CEC compliant TV or player is connected to this unit using HDMI
connection.
3. Start play on the AV component.
Input selector
HDMI MAIN/SUB
Inputs
TV
HDMI 1
HDMI 2
HDMI 3
TV
INPUT
TV’s REMOTE
56
Playback
BLUETOOTH
®
Playback
You can wirelessly play music on a smartphone or other BLUETOOTH wireless technology enabled device through the speakers connected to this unit. It is also
possible to transmit the audio from this unit to BLUETOOTH enabled headphones, wireless speakers, etc.
Playing audio from BLUETOOTH wireless technology enabled devices with this unit
Perform the following procedure when this unit is on.
Pairing
1. When you press the BLUETOOTH button, "Now Pairing..." appears on the
display, and the pairing mode is enabled.
2. Enable (turn on) the BLUETOOTH function of the BLUETOOTH enabled
device, and then select this unit from among the devices displayed. If a
password is requested, enter "0000".
• This unit is displayed as "Onkyo TX-NR5100 XXXXXX". This display
can be changed using the Friendly Name function ( →p108) or Onkyo
Controller ( →p120) (available on iOS or Android™).
• To connect another BLUETOOTH enabled device, press and hold the
button at least 5 seconds, and then perform step 2. This unit can store the
pairing information of up to 8 paired devices.
• The coverage area is approx. 48´/15 m. Note that connection is not always
guaranteed with all BLUETOOTH enabled devices.
Playing Back
1. Perform the connection procedure on the BLUETOOTH enabled device.
2. Playing the music le.
The input on this unit automatically switches to "BLUETOOTH".
Turn up the volume of the BLUETOOTH enabled device to an appropriate
level.
• Due to the characteristics of BLUETOOTH wireless technology, the sound
produced on this unit may slightly be behind the sound played on the
BLUETOOTH enabled device.
Onkyo TX-NR5100 XXX
The illustration shows an image.
57
Playback
Transmitting audio from this unit to BLUETOOTH wireless technology enabled devices
Pairing
1. Press the input selector you want to play.
• Select a source other than "BLUETOOTH". This function does not work if
you select "BLUETOOTH".
2. Press the button on the remote controller, select "5. Hardware" -
"Bluetooth" - "Bluetooth Transmitter", and press the ENTER button.
3. Select "On" for "Bluetooth Transmitter".
• If you select "On (Tx)", playback is from the Bluetooth wireless technology
enabled device only, and if you select "On (Main + Tx)", playback is from
both the Bluetooth wireless technology enabled device and the main unit.
Bluetooth Transmitter
Bluetooth Transmitter
Search Devices
Output Level
aptX HD
Low Latency Mode
Pairing Information
Device
Status
On (Tx)
Start
Variable
Off
Off
Clear
Ready
Set to “Off” if you are not using the Bluetooth Transmitter.
4. In "Search Devices", press ENTER.
• The search starts for BLUETOOTH wireless technology enabled devices
that are able to receive, then a list of relevant devices is displayed.
5. Select the device you want to output the audio from, and when you press
ENTER the message "Now Pairing…" is displayed and the two are paired.
• Depending on the BLUETOOTH wireless technology enabled device,
you may need to pair manually. If the device name does not appear in the
list, check the settings of the BLUETOOTH wireless technology enabled
device.
The illustration shows an image.
58
Playback
Playing Back
1. Do the play operations on the AV component connected to this unit. Do the
play operations on this unit when the input is TUNER or NET.
• If "Variable" has been selected for the "Output Level", the volume can be
adjusted on this unit. Adjust to a suitable volume on the connected Bluetooth
wireless technology enabled device beforehand. If "Fixed" is selected, adjust
the volume on the Bluetooth wireless technology enabled device.
• You cannot transmit audio to multiple BLUETOOTH wireless technology
enabled devices from this unit.
• The coverage area is approx. 48´/15 m. Note that connection is not always
guaranteed with all BLUETOOTH enabled devices.
• When "Bluetooth Transmitter" is "On (Tx)" or "On (Main + Tx)" and in the
following cases, when this unit detects a paired Bluetooth wireless technology
enabled device, it will automatically reconnect with that device.
– While other than "BLUETOOTH" is selected
– When the "NET" input is selected and there is audio output from a network
service/content (some services excluded)
When not using this function, select "O" in "Bluetooth Transmitter" to cancel
the connection. Also disconnect on the receiving device (if disconnection is
possible on the receiving device).
• Audio cannot be output from a BLUETOOTH wireless technology enabled
device in the following cases:
– When the audio le is DSD format
– When playing audio from one of the following network services:
Chromecast built-in, Amazon Alexa, AirPlay, DTS Play-Fi
• Sound quality adjustments and listening modes of this unit cannot be applied
to the output audio.
59
Playback
Listening To the Radio
You can receive AM/FM radio stations on this unit with the built-in tuner.
Listening To the AM/FM Radio
Tuning into a Radio Station
Perform the following procedure when this unit is on.
Tuning Automatically
1. Press TUNER repeatedly to select either "AM" or "FM".
2. Press MODE repeatedly to display "TunMode: Auto" on the display.
3. When you press the cursors / , automatic tuning starts, and searching
stops when a station is found. When tuned in to a radio station, the "TUNED"
indicator on the display lights up. When tuned in to an FM radio station, the
"FM ST" indicator lights up.
When FM broadcasts reception is poor: Perform the procedure for "Tuning
Manually" ( →p60). Note that if you tune manually, the reception for FM
broadcasts will be monaural rather than stereo, irrespective of the sensitivity of
the reception.
60
Playback
Tuning Manually
Note that if you tune manually, the reception for FM broadcasts will be monaural
rather than stereo, irrespective of the sensitivity of the reception.
1. Press TUNER repeatedly to select either "AM" or "FM".
2. Press MODE repeatedly to display "TunMode: Manual" on the display.
3. While pressing the cursors / , select the desired radio station.
• Each time you press the cursors / , the frequency changes by 1 step.
If the button is held down, the frequency changes continuously, and if the
button is released, the frequency stops changing.
/ / /
ENTER
MODE
TUNER
Frequency step setting
Press , and using the cursors and ENTER, select "6. Miscellaneous" - "Tuner"
- "AM/FM Frequency Step", and then select the frequency step for your area.
Presetting a Radio Station ( p61)
61
Playback
Presetting a Radio Station
Registration Procedure
You can preset up to 40 of your favorite radio stations.
After tuning in to the radio station you want to register, perform the following
procedure.
1. Press MEMORY so that the preset number on the display blinks.
2. While the preset number is blinking (approx. 8 seconds), repeatedly press the
cursors / to select a number between 1 and 40.
3. Press MEMORY again to register the station.
When the station is registered, the preset number stops ashing. Repeat this
procedure for all of your favorite radio stations.
/ / /
ENTER
MEMORY
CLEAR
TUNER
Selecting a Preset Radio Station
1. Press TUNER.
2. Press the cursors / to select a preset number.
Deleting a Preset Radio Station
1. Press TUNER.
2. Press the cursors / to select the preset number to delete.
3. After pressing MEMORY, press CLEAR while the preset number is blinking,
and delete the preset number. When deleted, the number on the display
disappears.
62
Playback
Listening Mode
This unit is equipped with a variety of listening modes, and you can select the optimum listening mode for movies, TV, music, and games by pressing MOVIE/TV,
MUSIC, and GAME. ( →p139)
• For details of the eects of each listening mode, refer to "Listening Mode Eects" ( →p145).
• For listening modes selectable for each audio format of input signals, refer to "Input Formats and Selectable Listening Modes" ( →p141).
Selecting a Listening mode
1. Press one from among MOVIE/TV, MUSIC, and GAME during playback.
2. Press the selected button repeatedly to switch the modes displayed on the
display of the main unit.
• Each of MOVIE/TV, MUSIC and GAME buttons stores the listening mode that
was selected last. If content incompatible of the listening mode selected last
is played, the most standard listening mode for the content is automatically
selected.
63
Playback
Checking the input format and listening mode
Repeatedly pressing the button on the remote controller switches the display
of the main unit in the following order.
• The content displayed depends on the source, BLUETOOTH, etc., being
played.
• Not all the information is necessarily displayed.
Input source and volume
Listening mode
Input format
The display is switched in
a few seconds.
Sampling frequency
Input signal resolution
64
Playback
Menu operations
You can quickly adjust the settings you frequently use, such as tone
adjustments, etc.
You can make the settings on the TV screen during playback. Press Q on the
remote controller to display the Quick Menu.
Quick Menu
HDMI
Audio
RoomEQ
Level
HDMI Out
A/V Sync
Audio Return Channel
BD/DVD
Select the item with the cursors / of the remote controller, and press the
ENTER button to conrm your selection.
Use the cursors to change the settings.
• To return to the previous screen, press .
• To exit the settings, press Q.
Quick Menu
65
Playback
HDMI
HDMI Out: Select the HDMI OUT jack to output video signals from "MAIN",
"SUB", and "MAIN+SUB".
A/V Sync: If the video is behind the audio, you can delay the audio to oset the
gap. The setting can be set for each input.
• It cannot be set if the listening mode is Pure Audio or Direct.
Audio Return Channel: You can enjoy the sound of the HDMI-connected ARC-
compatible TV through the speakers connected to the unit. Select "On" when
listening to the audio of TV using the speakers of this unit. Select "O" when the
ARC function is not used.
Audio
Music Optimizer: Improve the quality of the compressed audio. Playback sound
of lossy compressed les such as MP3 will be improved. The setting can be set
for each input. This works in signals whose sampling frequencies are 48 kHz or
less. The setting is not eective in the bitstream signals.
• It cannot be set if the listening mode is Pure Audio or Direct.
Late Night: Enable small sounds to be easily heard in detail. It is useful when
you need to reduce the volume while watching a movie late night.
• This function cannot be used in the following cases.
– When playing Dolby Digital Plus or Dolby TrueHD with "Loudness
Management" set to "O"
– When the input signal is DTS:X, and "Dialog Control" is not 0 dB
– When the input signal is Analog/DSD and the listening mode is Pure Audio
or Direct
Zone B: Select a method of outputting audio to ZONE B from among "O",
"On (A+B)" and "On (B)".
Digital Filter: You can switch the type of digital lter in the AUDIO DAC (digital
analog converter). You can choose "Slow" (gives the sound a soft and uid feel),
"Sharp" (gives the sound more structure and rmer feel) or "Auto" (auto). The
setting can be separately set to each input selector. This can be set when the
sampling frequency is 44.1 kHz or more.
RoomEQ
It cannot be set if the listening mode is Pure Audio or Direct.
AccuEQ: Enable or disable the equalizer function that corrects for sound
distortion caused by the acoustic environment of the room.
On (All Ch): EQ that corrects according to the room acoustics acquired with the
AccuEQ calibration is applied to all channels.
On (ex. L/R): The same EQ as "On (All Ch)" is applied to speakers other than the
Front Speakers. EQ correction for the Front Speakers is turned o.
• The setting can be separately set to each input selector.
Manual Equalizer: Select "Preset 1" to "Preset 3" congured in "2. Speaker"
- "Equalizer Settings" on the Setup menu. When this is set to "O", the same
sound eld setting is applied to all ranges.
Cinema Filter: Adjusts the soundtrack with the enhanced high range so that it
suits a home theater.
In this function, the following listening modes can be used: Dolby Audio - DD,
Dolby Audio - DD+, Dolby Audio - Surr, Dolby Audio - TrueHD, Multichannel,
DTS, DTS-ES, DTS 96/24, DTS-HD High Resolution, DTS-HD Master Audio,
DTS Neural:X, DTS Express and DSD
Level
Front: Adjust the speaker level of the front speakers while listening to the sound.
Center: Adjust the speaker level of the center speaker while listening to the
sound.
Subwoofer: Adjust the speaker level of the subwoofer while listening to the
sound.
• If you set the unit to the standby mode, the adjustments you made will be
restored to the previous statuses.
67
Playback
AirPlay
®
By connecting this unit to the same network as that of iOS devices such as iPhone
®
, iPod touch
®
and iPad
®
, you can enjoy music les on iOS devices wirelessly.
• Update the OS version on your iOS device to the latest version.
• Depending on the iOS version, operation screens or operation procedures on the iOS device may be dierent. For details, refer to the operating instructions for the
iOS device.
Basic Operations
1. Connect the iOS device to the access point where this unit is connected via
network.
2. Tap the AirPlay icon in the play screen of the music app on an iOS device
that supports AirPlay and select this unit from the list of devices displayed.
3. Play the music le on the iOS device.
• When "5. Hardware" - "Power Management" - "Network Standby" is set to
"O" in the Setup menu, turn this unit on manually, and press the NET button
on the remote controller. In the factory default setting, the Network Standby
function ( →p112) is set to On.
• Due to the characteristics of AirPlay wireless technology, the sound produced
on this unit may slightly be behind the sound played on the AirPlay-enabled
device.
You can also play the music les on a PC with iTunes (Ver. 10.2 or later)
equipped. Conrm that this unit and the PC are connected to the same network
beforehand. Then, press NET on the remote controller. Next, click the AirPlay
icon
in iTunes, select this unit from the displayed devices, and start play of a
music le.
Onkyo TX-NR5100 XXXXXX
iPhone
Wi-Fi
e.g., iOS 10
68
Playback
Playing Back on multiple devices (AirPlay2)
This unit supports AirPlay2. If the version of the iOS device is iOS11.4 or later,
you can play the tracks on the iOS device simultaneously on this device and on
another device that supports AirPlay2.
1. Connect the iOS device to the access point where this unit is connected via
network.
2. Tap the AirPlay icon on the play screen of the music play application on
the iOS device, and select this unit and AirPlay2-supported devices to play
from the displayed devices.
• AirPlay2-supported devices are displayed with white circle on the right
side.
• Multiple AirPlay2-supported devices can be selected.
• The volume can be adjusted on individual devices.
3. Play the music le on the iOS device.
• When "5. Hardware" - "Power Management" - "Network Standby" is set to
"O" in the Setup menu, turn this unit on manually, and press the NET button
on the remote controller. In the factory default setting, the Network Standby
function ( →p112) is set to On.
• Due to the characteristics of AirPlay wireless technology, the sound produced
on this unit may slightly be behind the sound played on the AirPlay-enabled
device.
You can also play the music les on a PC with iTunes (Ver. 12.8 or later)
equipped. Conrm that this unit and the PC are connected to the same network
beforehand. Then, press NET on the remote controller. Next, click the AirPlay
icon
in iTunes, select this unit and AirPlay2-supported devices to play from
the displayed devices, and start play of a music le.
Onkyo TX-NR5100 XXXXXX
iPhone
Onkyo XXXXXXXX
Onkyo XXXXXXXX
Wi-Fi
e.g., iOS 11.4
69
Playback
DTS Play-Fi
®
https://play-.com/
When connecting this unit to the same network as mobile devices, such as
a smartphone and tablet, you can enjoy music played on the mobile device
wirelessly. Music from a streaming distribution service or music in the music
library on a mobile device can be played. This function also supports a playlist
on iTunes. Also, connecting multiple speakers supporting DTS Play-Fi on
the same network will enable "Group playback" that plays the same music in
separate rooms at home. To enjoy this function, download Onkyo Music Control
App (available on iOS or Android™).
Playing Back
1. Download Onkyo Music Control App using your mobile device.
https://www.onkyo.com/play/app_o.html
2. Connect the mobile device to the network where this unit is connected.
3. Starting up Onkyo Music Control App will automatically display compatible
devices.
4. Select this device from the compatible devices. Then, a list of applications
such as a music streaming distribution service is displayed. Select
the content to play, and perform operation according to the on-screen
instructions.
• When "5. Hardware" - "Power Management" - "Network Standby" is set to
"O" in the Setup menu, turn this unit on manually, and press the NET button
on the remote controller. In the factory default setting, the Network Standby
function ( →p112) is set to On.
• For detailed operation and FAQ, visit the following URL.
https://www.onkyo.com/play/info_o.html
• To use a music streaming distribution service, user registration may be
required.
• This unit does not support the following DTS Play-Fi functions.
– Spotify
– Wireless Surround Sound
– Line In Rebroadcast
– Internet Radio
• Some of the settings in the "Setup menu" cannot be changed on this unit. To
change those settings, cancel the connection of this unit from the application.
• Listening modes cannot be selected during playback.
70
Playback
Alexa is a cloud-based voice service developed by Amazon. When this unit is
registered with an Amazon account, you can use a terminal with Amazon Alexa
(an Amazon Echo, etc.) or Amazon Alexa App (available on iOS and Android™)
to perform operations such as adjusting the volume of this unit or playing music
using voice commands.
• You need an Amazon account to use Amazon Alexa. For more information,
see the Amazon website.
Registering this unit with an Amazon
account
1. Register with the Amazon account on Onkyo Controller. This cannot be set
with operations on this unit.
Refer to "Onkyo Controller" ( →p120) for information about the app.
2. Start Onkyo Controller and tap the unit when displayed.
3. Tap "NET" or "NETWORK" at the top of the Onkyo Controller screen, and
after switching to the network menu, tap the "amazon alexa" icon.
• If the login screen is not displayed but an update or installation screen is
displayed instead, perform the update or installation according to the on-
screen instructions.
Available services may dier depending on your area.
4. Tap "Start Setup", and in the Setup screen, select the language and register
the device name. Select the same language as the one you have selected
for your other terminals with Amazon Alexa (an Amazon Echo, etc.). For the
device name, use one that can easily be called up vocally.
For example: Speaker
5. Tap "Next" to display the Amazon Alexa screen.
6. Follow the on screen instructions to enter the Amazon account information,
such as your email address and password, to log into Amazon (*1). After
logging in, tap "Allow" and register this unit with an Amazon account.
Amazon Alexa
71
Playback
(*1) Log in using the same account as other terminals with Amazon Alexa.
7. When registration is nished, the screen returns to the one for Onkyo
Controller. Follow the on screen instructions and talk to the terminal with
Amazon Alexa (an Amazon Echo, etc.), and conrm that you can use voice
commands.
For example: "Alexa, raise the volume of the speaker (*2)"
"Alexa, play music from the speaker (*2)"
(*2) Use the device name you registered in Step 4 when talking.
Operating this unit
You can use voice commands to adjust the volume on this unit, start and stop
music, and skip music up or down.
1. With the unit on, speak at the terminal with Amazon Alexa (an Amazon Echo,
etc.). When using the Amazon Alexa app, after starting the app, tap the Alexa
logo and speak at the mobile device.
For example: "Alexa, raise the volume of the speaker (*3)"
"Alexa, play music from the speaker (*3)"
(*3) Use the device name you registered in Step 4 of "Registering this unit
with an Amazon account" when talking.
• Refer to the website for details about voice commands. (Click here )
• It is not possible to turn the unit on or o, or to switch the listening mode.
• Refer to the Amazon websites for information about operation of the Amazon
Alexa app.
72
Playback
Amazon Music
Registering this unit with Amazon Music allows you to enjoy the music
distribution service provided by Amazon.
• To play Amazon Music, you need to have your Amazon account and sign up
for Amazon Prime or Amazon Music Unlimited. For more information, see the
Amazon website.
Amazon Music is now available in several countries. If Amazon Music is not
available in your country, please visit https://music.amazon.com/ for more info.
Registering This Unit with Amazon Music
1. Register with the Amazon account on Onkyo Controller. This cannot be set
with operations on this unit.
Refer to "Onkyo Controller" ( →p120) for information about the app.
2. Start Onkyo Controller and tap the unit when displayed.
3. Tap "NET" or "NETWORK" on the upper part of the Onkyo Controller’s
screen to switch to the network menu. Then tap the "Amazon Music" icon to
display the login screen of Amazon Music. (Depending on the model, the icon
names may be dierent.)
• If the login screen is not displayed but an update or installation screen is
displayed instead, perform the update or installation according to the on-
screen instructions.
Available services may dier depending on your area.
4. Enter the Amazon account information such as email address and password
to log in to Amazon. When the login is successful and this unit is registered,
the Amazon Music menu is displayed.
For playback, proceed to step 3 in the next section.
73
Playback
Playing Amazon Music using the Onkyo
Controller
1. Start up Onkyo Controller. This unit is automatically displayed after startup.
Then, tap and select this unit displayed.
2. Tap "NET" or "NETWORK" on the upper part of the screen to switch to the
network screen. Then tap the "Amazon Music" icon.
3. Select the content to play from the menu screen of Amazon Music to start
playback.
Playing Amazon Music using the remote
controller
1. Switch the input on the TV to the input connected to the unit.
2. Pressing NET will display the Network Functions list screen on the TV.
3. Select "Amazon Music" with the cursors and press ENTER to conrm.
4. Select the content to play from the menu screen of Amazon Music to start
playback.
74
Playback
Registering this unit with TIDAL allows you to enjoy the music distribution
service provided by TIDAL. You can register this unit on the screen of Onkyo
Controller by downloading Onkyo Controller (available on iOS or Android™) to
mobile devices such as a smartphone and tablet.
• You need a TIDAL account to play back TIDAL. For more information, see the
TIDAL website.
Registering this unit with TIDAL
• You can register this unit with TIDAL using Onkyo Controller. The registration
cannot be performed by operation of this unit.
1. Connect this unit to your home network by the network settings on this unit.
2. Download Onkyo Controller using your mobile device.
3. Connect the mobile device to the network where this unit is connected.
4. Start up Onkyo Controller to automatically display this unit. Tap and select
this unit displayed.
5. Tap "NET" or "NETWORK" on the upper part of the Onkyo Controller’s
screen to switch to the network menu. Then tap the "TIDAL" icon to display
the login screen of TIDAL. (Depending on the model, the icon names may be
dierent.)
• If the login screen is not displayed but an update or installation screen
is displayed instead, perform the update or installation according to the
onscreen instructions.
Available services may dier depending on your area.
6. Enter the TIDAL account information such as login ID and password to log in
to TIDAL. When the login is successful and this unit is registered, the TIDAL
menu is displayed.
For playback, proceed to step 3 in the next section.
Playing TIDAL
1. Start up Onkyo Controller. This unit is automatically displayed after startup.
Then, tap and select this unit displayed.
2. Tap "NET" or "NETWORK" on the upper part of the screen to switch to the
network screen. Then tap the "TIDAL" icon.
3. Select the content to play from the menu screen of TIDAL to start playback.
• To play TIDAL using the remote controller, operate the input selector on the
remote controller to display the network menu, and select "TIDAL" from the
menu.
TIDAL
75
Playback
Connecting the Sonos System for Playback
Connecting this unit and Sonos Connect allows you to send the music or music
sources on the Sonos App to this unit. Through Sonos Connect, you can play
this unit with the same group of another Sonos device on the network or can
play only on this unit. Also, if you start to play music from Sonos App, this unit is
automatically turned on and the link function to switch input works.
• When "5. Hardware" - "Power Management" - "Network Standby" is set to
"O" in the Setup menu, turn this unit on manually, and press the NET button
on the remote controller. In the factory default setting, the Network Standby
function ( →p112) is set to On.
• You can register a maximum of 2 Sonos Connect.
Necessary Equipment
• Sonos Connect
• RCA audio cable (supplied with Sonos Connect)
How to Connect This Unit and Sonos
Connect
1. Connect the Sonos Connect to the AUDIO IN jack of this unit with the RCA
audio cable supplied with the Sonos Connect. Any input jacks other than the
PHONO jack can be used.
• A digital cable can also be connected. For details, refer to the instruction
manual of Sonos.
• You can change the name of the input selector displayed on this unit to
easier-to-understand name. For example, the input connected to Sonos
Connect can be changed from "CD" (or another input selector name) to
"SONOS". Press the
button on the remote controller, select "4. Source"
- "Name Edit" and then change the name.
Setting Up
A setup is required to play Sonos on this unit. Make the setting according to the
following procedure.
1. Press the button on the remote controller, select "5. Hardware" - "Works
with SONOS", and press the ENTER button.
2. Select the following items with the cursors / and set each item.
Input Selector:
Enable the interlocking function with the Sonos Connect. With the cursors /
, select the input selector to which the Sonos Connect is connected.
Connected Device:
Press the ENTER button to display Sonos devices connected to the same
network as the network of this unit. Select the Sonos Connect connected to
the unit and press the ENTER button.
• Products (e.g. Play:3 unequipped with an output terminal) other than the
Sonos Connect are also displayed in the device list and selectable. In
that case, when playback on the Sonos side starts, the input is switched,
however, audio is not output. Select the room name of the connected
Sonos Connect.
• Up to 32 devices can be displayed on the Sonos product list screen. If you
76
Playback
cannot nd the Sonos Connect to be interlocked, return to the previous
screen, turn o the product you do not want to interlock, and try again.
Preset Volume:
You can set the volume beforehand for playing back the Sonos Connect in
the main room (where this unit is located). Select a value from "Last" (Volume
level before entering standby mode), "Min", "0.5" to "99.5" and "Max".
Playing Sonos on This Unit
1. Select desired tracks using Sonos App and send the tracks to the room
where this unit is located (or to the group). It is recommended to give an easy-
to-remember name to the combination of this unit and Sonos Connect, such
as TV Room or Living Room where this unit is located.
• If the input selector of this unit is not automatically switched even after the
start of music playback, stop the playback once and start again.
• When the "Volume Pass Through" mode has been selected with the Sonos
App settings, you can use the Sonos App to control the volume of this unit.
* You cannot use the "Preset Volume" function when the "Volume Pass
Through" mode has been selected.
77
Playback
Internet Radio
By connecting this unit to an Internet-connected network, you can enjoy Internet radio services such as TuneIn Radio.
• To play Internet radio services, the network needs to be connected to the Internet.
• Depending on the Internet radio service, a user registration may be required on your PC beforehand. For details of each service, visit the website of each service.
Playing Back
Perform the following procedure when this unit is on.
1. Switch the input on the TV to the input connected to the unit.
2. Pressing NET will display the Network Functions list screen on the TV.
3. Select your preferred Internet radio service using cursor, and press ENTER to
conrm the selection.
4. Following the on-screen instructions, select a radio station and program using
cursor, and then press ENTER to play.
• To return to the previous screen, press .
/ / /
ENTER
NET
Inputs
TV
HDMI 1
HDMI 2
HDMI 3
TV
INPUT
TV’s REMOTE
The illustration shows an image.
78
Playback
Internet Radio Service Menu
You can bookmark specic stations, or delete stations that have been
bookmarked. The displayed menu varies according to the service being
selected.
The menu icon
is displayed while a station is being played. When only this
icon is displayed, pressing ENTER will display the menu on the screen. When
multiple icons are displayed, select the
icon with the cursor, and press
ENTER.
Regarding the TuneIn Radio Account
If you create an account on the TuneIn Radio website (tunein.com), and log in it
from this unit, your favorite radio stations or programs you have followed on the
website are automatically added to your "My Presets" on this unit. "My Presets"
is displayed on the next level in the hierarchical structure of TuneIn Radio. To
display a radio station added to "My Presets", you need log into TuneIn Radio
from the unit. To log in, select "Login" - "I have a TuneIn account" in the "TuneIn
Radio" top list on the unit, and then enter your user name and password.
• If you select "Login" on this unit, a registration code is displayed. By using
this code, you can associate the device on the My Page section of the TuneIn
Radio website so that you can log in from "Login" - "Login with a registration
code" without entering the user name and password.
79
Playback
Playing different audio and video
Displaying Your Favorite Video on TV While Playing Music
While listening to the music from a CD or BLUETOOTH enabled device, you can
display video on TV from an AV component such as a Blu-ray Disc player.
• For audio playback, you can select an input selector to which video input is
not assigned, such as "CD", "TUNER", "NET" and "BLUETOOTH".
Perform the following procedure when this unit is on.
1. Switch the input on the TV to the input connected to the unit.
2. Press an input selector such as BD/DVD button connected to the AV
component of which the video is to be displayed on TV.
• This operation is not necessary if the same input selector has been
selected in the previous operation.
3. Press an input selector of the audio you want to play, such as the CD or
BLUETOOTH button and perform playback operation.
4. Perform the playback operation of the AV component such as a Blu-ray Disc
player. To play the audio of NET or BLUETOOTH, the following step 5
operation is required.
5. To play the audio of NET or BLUETOOTH, press the MODE button to switch
the TV display from the NET or BLOOTOOTH playback screen to the video of
the AV component. Pressing the MODE button again will return to the NET or
BLOOTOOTH playback screen.
• When the TV display is switched to the video of the AV component, the
playback screen of NET or BLUETOOTH is displayed on the corner of the
screen as Mini Player. The setting for Mini Player can be changed on the
Setup Menu so that it automatically turns o in 30 seconds after displayed.
("Mini Player OSD" ( →p94))
Setting the video source to be displayed on TV beforehand: When playing
the audio of "TUNER", "NET" and "BLUETOOTH", you can set the input selector
to be displayed on TV beforehand using "Video Select" ( →p104) on the Setup
Menu. If a value other than "Last" is set, step 2 in the operation procedure is not
required.
The illustration shows an image.
80
Playback
USB Storage Device
You can play music les stored on a USB storage device.
Supported Audio Formats
MP3 (.mp3)
•
MPEG-1/MPEG-2 Audio Layer 3/44.1 kHz, 48 kHz/Between 8 kbps and 320 kbps,
and VBR
WMA (.wma)
• 44.1 kHz, 48 kHz/Between 5 kbps and 320 kbps, and VBR
• WMA Pro/Voice/WMA Lossless formats are not supported.
WAV (.wav)
WAV les contain uncompressed PCM digital audio.
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
AIFF (.ai/.aif)
AIFF les contain uncompressed PCM digital audio.
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
AAC (.aac/.m4a/.mp4/.3gp/.3g2)
• MPEG-2/MPEG-4 Audio/44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/Between 8 kbps
and 320 kbps, and VBR
FLAC (.ac)
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
LPCM (Linear PCM)
• 44.1 kHz, 48 kHz/16 bit
Apple Lossless (.m4a/.mp4)
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/16 bit, 24 bit
DSD (.dsf/.d)
• DSF/DSDIFF/2.8 MHz, 5.6 MHz, 11.2 MHz
USB Storage Device Requirements
• This unit can use USB storage devices that comply with the USB mass
storage class standard. Also the format of USB storage devices supports
FAT16 or FAT32 le system format.
• If the USB storage device has been partitioned, each section will be treated
as an independent device.
• Up to 20,000 tracks per folder are supported, and folders can be nested up to
16 levels deep.
• USB hubs and USB storage devices with hub functions are not supported. Do
not connect these devices to the unit.
• If an AC adapter is supplied with the USB storage device, connect the AC
adapter, and use it with a household outlet.
• USB storage devices with security functions are not supported on this unit.
• Media inserted to the USB card reader may not be available in this function.
Furthermore, depending on the USB storage device, proper reading of the
contents may not be possible.
• In use of a USB storage device, our company accepts no responsibility
whatsoever for the loss or modication of data stored on a USB storage
device, or malfunction of the USB storage device. We recommend that you
back up the data stored on a USB storage device before using it with this unit.
• Note that operation is not always guaranteed for all USB storage devices.
Playing music files saved on a USB storage
device ( →p81)
81
Playback
Playing music les saved on a USB storage device
Perform the following procedure when this unit is on.
1. Switch the input on the TV to the input connected to the unit.
2. Plug your USB storage device with the music les into the USB port on the
rear panel of this unit.
3. Press NET to display the network service list screen.
4. Select "USB" with the cursors, and then press ENTER.
• If the "USB" indicator blinks on the display, check whether the USB storage
device is plugged in properly.
• Do not unplug the USB storage device while "Connecting..." is being
displayed on the display. This may cause data corruption or malfunction.
5. Press ENTER on the next screen again. The list of folders and music les on
the USB storage device is displayed. Select the folder with the cursors, and
press ENTER to conrm your selection.
6. Select the music le with the cursors, and then press ENTER to start
playback.
/ / /
ENTER
NET
• To return to the previous screen, press .
• Characters that cannot be displayed on this unit appear with "".
• The USB port of this unit complies with the USB 2.0 standard. The transfer
speed may be insucient for some content you play, and sound interruptions,
etc. may occur.
82
Playback
• When playing les recorded with VBR (Variable bit-rate), the playback time
may not be displayed correctly.
• This unit supports the gapless playback of the USB storage device in the
following conditions.
When continuously playing WAV, FLAC and Apple Lossless les with the
same format, sampling frequency, the number of channels and quantization
bit rate.
• To display an album title, artist name and album art of a le in WAV format,
make the folder structure and le names as shown below when saving music
les. The album art can be displayed by saving a .jpg le to display on the
screen in the folder of bottom level. Note that a large volume of .jpg le may
take time to be displayed, or may not be displayed.
Folder 1
Artist name
Folder 1-1
Album name
file 1-1
file 2-1
file 3-1
Folder 1-2
Album name
file 1-2
file 2-2
file 3-2
.jpg file
.jpg file
83
Playback
Music Server
Streaming play of music les stored on PCs or NAS devices connected to the same network as this unit is supported.
• The network servers this unit is compatible with are those PCs with players installed that have the server functionality of Windows Media
®
Player 12, or NAS that
are compatible with home network functionality. When using Windows Media
®
Player 12, you need to make the settings beforehand. Note that with PCs, only music
les registered in the library of Windows Media
®
Player can be played.
Supported Audio Formats
MP3 (.mp3)
•
MPEG-1/MPEG-2 Audio Layer 3/44.1 kHz, 48 kHz/Between 8 kbps and 320 kbps,
and VBR
WMA (.wma)
• 44.1 kHz, 48 kHz/Between 5 kbps and 320 kbps, and VBR
• WMA Pro/Voice/WMA Lossless formats are not supported.
WAV (.wav)
WAV les contain uncompressed PCM digital audio.
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
AIFF (.ai/.aif)
AIFF les contain uncompressed PCM digital audio.
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
AAC (.aac/.m4a/.mp4/.3gp/.3g2)
• MPEG-2/MPEG-4 Audio/44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/Between 8 kbps
and 320 kbps, and VBR
FLAC (.ac)
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
LPCM (Linear PCM)
• 44.1 kHz, 48 kHz/16 bit
Apple Lossless (.m4a/.mp4)
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/16 bit, 24 bit
DSD (.dsf/.d)
• DSF/DSDIFF/2.8 MHz, 5.6 MHz, 11.2 MHz
Windows Media
®
Player 12 settings
1. Turn on your PC, and start Windows Media
®
Player 12.
2. In the "Stream" menu, select "Turn on media streaming" to display a dialog
box.
• If the media streaming is already turned on, select "More streaming
options..." in the "Stream" menu to display the list of playback devices in
the network, and then go to step 4.
3. Click "Turn on media streaming" to display the list of playback devices in the
network.
4. Select this unit in "Media streaming options" and check that it is set to "Allow".
5. Click "OK" to close the dialog.
6. Open the "Stream" menu and conrm that "Allow remote control of my
Player..." is checked.
Playing Back ( →p84)
84
Playback
Playing Back
Perform the following procedure when this unit is on.
1. Switch the input on the TV to the input connected to the unit.
2. Start the server (Windows Media
®
Player 12 or NAS device) containing the
music les to play.
3. Make sure that the PC or NAS is properly connected to the same network as
this unit.
4. Press NET to display the network service list screen.
• If the "NET" indicator on the display blinks, the unit is not properly
connected to the network. Check the connection.
5. With the cursors, select "Music Server", and then press ENTER.
/ / /
ENTER
NET
Inputs
TV
HDMI 1
HDMI 2
HDMI 3
TV
INPUT
TV’s REMOTE
The illustration shows an image.
85
Playback
6. Select the target server with the cursors, and press ENTER to display the
items list screen.
• This unit cannot access pictures and videos stored on servers.
• Depending on the server sharing settings, contents stored on the server
may not be displayed.
7. With the cursors, select the music le to play, and then press ENTER to start
playback.
• If "No Item." is displayed on the screen, check whether the network is
properly connected.
• To return to the previous screen, press
.
• When playing les recorded with VBR (Variable bit-rate), the playback time
may not be displayed correctly.
• For music les on a server, up to 20,000 tracks per folder are supported, and
folders can be nested up to 16 levels deep.
• Depending on the type of media server, the unit may not recognize it, or may
not be able to play its music les.
Searching music les to select
If the server you use supports search functions, the following search function
can be used.
Perform the following procedure with available servers displayed using Music
Server.
1. With
/ , select the server containing music les you want to play, and
press ENTER.
2. With
/ , select the Search folder, and press ENTER. The Search folder
contains the following three folders.
• "Search by Artist": Select this when searching by artist name.
• "Search by Album": Select this when searching by album title.
• "Search by Track": Select this when searching by track title.
3. With / , select the folder, and press ENTER.
4. Input a character string to search for, and press ENTER. Then, the search
result is displayed.
5. With
/ , select the music les to play, and press ENTER.
Controlling Remote Playback from a PC
You can use this unit to play music les stored on your PC by operating the PC
in your home network. The unit supports remote playback via Windows Media
®
Player 12. To use the remote playback function of this unit with Windows Media
®
Player 12, it must be congured beforehand. ( →p83)
Remote playback
1. Turn on the power of the unit.
2. Turn on your PC, and start Windows Media
®
Player 12.
3. Select and right-click the music le to play with Windows Media
®
Player 12.
• To remotely play a music le on another server, open the target server
from "Other Libraries", and select the music le to play.
4. Select this unit in "Play to" to open the "Play to" window of Windows Media
®
Player 12, and start playback on this unit.
• If your PC is running on Windows
®
8.1, click "Play to", and select this unit.
If your PC is running on Windows
®
10, click "Cast to Device", and select
this unit. Operations during remote playback are possible from the "Play
to" window on the PC. The playback screen is displayed on the HDMI-
connected TV.
5. Adjust the volume using the volume bar on the "Play to" window.
• Sometimes, the volume displayed on the remote playback window may
dier from the volume displayed on the display of this unit.
• When the volume is changed on this unit, the value is not reected in the
"Play to" window.
• This unit cannot play music les remotely in the following conditions.
– It is using a network service.
– It is playing a music le on a USB storage device.
• Remote play of FLAC and DSD is not supported.
• Remote playback does not support the gapless playback.
86
Playback
Play Queue
When downloading Onkyo Controller (available on iOS or Android™) to mobile
devices, such as a smartphone and tablet, you can save your favorite playlist
(Play Queue information) among music les stored in the USB storage device
connected to this unit and music les stored in PC or NAS connected to the
same network as this unit, and you can play the music on the playlist. The Play
Queue information is eective until the power cord of this unit is removed from
the outlet. Refer to "Onkyo Controller" ( →p120) for information about the app.
Adding Play Queue Information
1. Select the "INPUT" input on the application screen, and tap the "USB" icon.
Or, select the "NET" input, and tap the "USB" icon or "Music Server" icon.
(Depending on the model, the icon names may be dierent.)
2. Tapping the "+" icon of the track you want to add will open the pop-up to add
the Play Queue information.
3. Touch the "Play Now ", "Play Next " or "Play Last " icon to add the
track to Play Queue.
• If there are no tracks on the Play Queue list, only "Play Now " is
displayed.
Sort and Delete
1. Select the "NET" input, tap the "Play Queue" icon, and enter the Play Queue
service screen.
87
Playback
2. Tap the " " icon of the track to sort, and drag the icon to the destination.
3.
To delete a track, slide the track to the left until the trash icon changes to " ".
If
the device is on iOS, slide the " " icon to the left. Releasing your nger will
delete the track from Play Queue.
Playing Back
Playback starts when you select "Play Now " for Play Queue addition, or
select the track in the Play Queue service screen.
88
Playback
Connecting a transmitter for playback
When you connect wireless headphones or a wireless speaker transmitter to the ZONE B PRE/LINE OUT terminal of this unit, you can play back the same source
through the wireless headphones or wireless speakers as in the main room.
Connections
1. Use an analog audio cable to connect the ZONE B PRE/LINE OUT terminal
on this unit to the input terminal on the transmitter.
a
Transmitter
Playing Back
1. Press the Q button on the remote controller and select "Audio" - "Zone B".
2. Select the audio output destination.
O: Outputs audio only from ZONE A. "A" on the display of the main unit
lights up.
On (A+B): Outputs audio from both ZONE A and ZONE B. "A" and "B" on the
display of the main unit light up.
On (B): Outputs audio only from ZONE B. "B" on the display of the main unit
lights up.
3. Start play on the AV component.
4. Adjust the volume on the transmitter, etc., in ZONE B.
• If "On (A+B)" is selected as an audio output destination, you can select only
the "Stereo" listening mode for ZONE A when using the 2.1 ch speaker layout.
When using a speaker layout of 3.1 ch or more, you can select only the "AllCh
Stereo" listening mode.
a Analog audio cable
90
Setup
Setup Menu
Menu list
1. Input/Output Assign
1. TV Out / OSD Make settings for TV output and On-Screen Displays (OSD) that appear on the TV. p92
2. HDMI Input You can change input assignment between the input selectors and HDMI IN jacks.
p94
3. Digital Audio Input Change input assignment between the input selectors and DIGITAL IN COAXIAL/OPTICAL jacks.
p95
4. Analog Audio Input Change input assignment between the input selectors and AUDIO IN jacks.
p95
2. Speaker 1. Conguration Change the settings of connection environment of the speakers.
p96
2. Crossover Change the settings of crossover frequencies.
p97
3. Distance Set the distance from each speaker to the listening position.
p98
4. Level Calibration Adjust the volume level of each speaker.
p98
5.
Dolby Enabled Speaker
Change the settings of Dolby Enabled Speakers. p99
6. Equalizer Settings You can adjust the output volume of the range for each connected speaker.
p99
7. Speaker Virtualizer The Speaker Virtualizer function can be switched between On and O.
p100
3. Audio Adjust 1. Multiplex/Mono Change the settings of multiplex audio playback.
p101
2. Dolby Change the setting of when Dolby signals are input.
p101
3. DTS Change the setting of when DTS signals are input.
p102
4. LFE Level Set the low-frequency eect (LFE) level for Dolby Digital series, DTS series, Multichannel PCM,
and DSD signals.
p102
5. Volume Change the Volume settings.
p102
Use the on-screen displays (OSD) that appear on the TV to make the settings.
Press
on the remote controller to display the Setup menu.
Select the item with the cursors / of the remote controller, and press the ENTER button to conrm your selection.
Use the cursors / to change the default values.
• To return to the previous screen, press .
• To exit the settings, press the button.
Setup
1. Input/Output Assign
2. Speaker
3. Audio Adjust
4. Source
5. Hardware
6. Multi Zone
7. Miscellaneous
1. TV Out / OSD
2. HDMI Input
3. Video Input
4. Digital Audio Input
5. Analog Audio Input
Setup
1. Input/Output Assign
2. Speaker
3. Audio Adjust
4. Source
5. Hardware
6. Miscellaneous
1. TV Out / OSD
2. HDMI Input
3. Digital Audio Input
4. Analog Audio Input
91
Setup
4. Source 1. My Input Volume Set a volume value for each input selector. p103
2. Name Edit Set an easy name for each input.
p103
Audio Select Select the prioritized input terminal when multiple audio sources are connected to one input
selector.
p103
Video Select When "TUNER", "NET", or "BLUETOOTH" input is selected, you can set the input from which
video is displayed on the TV.
p104
5. Hardware 1. HDMI Change the settings for the HDMI functions.
p105
2. Network Change the settings for the Network functions.
p107
3. Bluetooth Change the settings for the BLUETOOTH function.
p110
4. Power Management Change the settings for the power-save function.
p112
5. Works with SONOS Change the settings to connect with the Sonos Connect.
p113
6. Miscellaneous 1. Tuner Change the settings for Tuner.
p114
2. Remote ID Change the remote controller ID.
p114
3. Firmware Update Change the settings for Firmware Update.
p115
4. Initial Setup Make the initial setup from the setup menu.
p115
5. Lock Lock the Setup menu so that the settings cannot be changed.
p115
6. Factory Reset All the settings are restored to factory defaults.
p115
92
SetupSetup
1. Input/Output Assign1. Input/Output Assign
1. TV Out / OSD
Make settings for TV output and On-Screen Displays (OSD) that appear on the
TV.
HDMI Out (Default Value: MAIN)
Select the HDMI jack to be connected with the TV.
• If devices with dierent resolutions are connected to HDMI OUT MAIN jack
and SUB jack, images are output with the lower resolution.
MAIN When connecting the TV to the HDMI OUT MAIN jack
SUB When connecting the TV to the HDMI OUT SUB jack
MAIN+SUB When connecting to both the MAIN and SUB jacks
Dolby Vision (Default Value: MAIN)
To output Dolby Vision video from the player to a TV that supports Dolby Vision,
select either the HDMI OUT MAIN jack or HDMI OUT SUB jack to which the
Dolby Vision-supported TV is connected. This setting is only necessary if you
have set "HDMI Out" to "MAIN+SUB" and you have connected a TV to both the
MAIN and SUB jacks.
MAIN To output Dolby Vision video to a Dolby Vision-supported TV
connected to the HDMI OUT MAIN jack
SUB To output Dolby Vision video to a Dolby Vision-supported TV
connected to the HDMI OUT SUB jack
O After selecting "MAIN" or "SUB", if the video on the TV does
not appear correctly
Upscaling (Default Value: O)
When a TV supporting 4K is used, video signals input with 1080p can be
automatically output with 4K.
• If the TV does not support the 4K resolution with the same frequency as
the frequency of HDMI input video signals, upscaling to 4K is not correctly
performed. Check the frequency of 4K resolution supported by the TV, and
change the resolution of the video signals input from the AV component.
O When this function is not used
• If your TV does not support 4K, set it to "O".
Auto When this function is used
Super Resolution (Default Value: 2)
When "Upscaling" is set to "Auto", select the correction level of the input video
signals from "O" and "1" (weak) to "3" (strong).
93
SetupSetup
1. Input/Output Assign
HDMI 4K/8K Signal Format
Set the 4K/8K signal format input and output by this unit. Set to suit the TV or
player connected.
• For resolutions supported by this unit, refer to "Supported input
resolutions" ( →p154).
BD/DVD (Default Value: 4K Enhanced)
GAME (Default Value: 4K Enhanced)
CBL/SAT (Default Value: 4K Enhanced)
STRM BOX (Default Value: 4K Enhanced)
PC (Default Value: 4K Enhanced)
CD (Default Value: 4K Enhanced)
TV (Default Value: 4K Enhanced)
4K Standard When using a High Speed HDMI Cable that supports
10.2 Gbps to connect a TV or player compatible with standard
4K signal formats (4K 30Hz, etc.)
4K Enhanced When using a Premium High Speed HDMI Cable that supports
18 Gbps to connect a TV or player compatible with high-
denition 4K signal formats (4K 60Hz, 4K HDR, etc.)
• There may be some image disruption depending on the
connected component and the HDMI cable. If this occurs,
switch to "4K Standard".
8K Standard When using an 18 Gbps-compatible PREMIUM High Speed
HDMI Cable or a 48 Gbps-compatible ULTRA High Speed
HDMI Cable to connect a TV or player compatible with
4K/120p or 5K, 8K signal formats
OSD Language (Default Value: English)
Select the on-screen display language from the following.
English, German, French, Spanish, Italian, Dutch, Swedish
Impose OSD (Default Value: On)
Set whether or not to display information such as volume adjustment or
switching of input on the TV screen.
On OSD is displayed on the TV
• OSD may not be displayed depending on the input signal
even if "On" is selected. In this case, change the resolution
of the connected device.
O OSD is not displayed on the TV
94
SetupSetup
1. Input/Output Assign
Mini Player OSD (Default Value: Always On)
You can display on the TV the images from another input selected last while
playing the audio from NET or BLUETOOTH input. After switching the input to
NET or BLUETOOTH, play the images and audio. And then when you press
MODE on the remote controller, the image is displayed in full-screen mode, and
the audio information (Mini Player) for NET or BLUETOOTH is displayed in the
corner of the screen. You can set whether to always display this Mini Player on
the screen.
• Each time the MODE button is pressed, the image display/non-display can be
switched.
• This setting cannot be selected if "Impose OSD" is set to "O".
Always On The Mini Player is always displayed.
Auto O The Mini Player turns o automatically in 30 seconds after
displayed. If operation such as changing the volume is
performed, it is displayed again for 30 seconds.
Screen Saver (Default Value: 3 minutes)
Set the time to start the screen saver.
Select a value from "3 minutes", "5 minutes", "10 minutes" and "O".
2. HDMI Input
You can change input assignment between the input selectors and HDMI IN
jacks.
BD/DVD (Default Value: HDMI 1 (HDCP 2.3))
GAME (Default Value: HDMI 2 (HDCP 2.3))
CBL/SAT (Default Value: HDMI 3 (HDCP 2.3))
STRM BOX (Default Value: HDMI 4 (HDCP 2.3))
PC (Default Value: ---)
CD (Default Value: ---)
TV (Default Value: ---)
"HDMI 1 (HDCP 2.3)" to "HDMI 4 (HDCP 2.3)":
Assign any HDMI IN jack to each of the input selectors. If you do not assign a
jack, select "---". To select an HDMI IN jack already assigned to another input
selector, change its setting to "---" rst.
95
SetupSetup
1. Input/Output Assign
3. Digital Audio Input
Change input assignment between the input selectors and DIGITAL IN
COAXIAL/OPTICAL jacks. If you do not assign a jack, select "---".
BD/DVD (Default Value: ---)
GAME (Default Value: ---)
CBL/SAT (Default Value: ---)
STRM BOX (Default Value: ---)
PC (Default Value: ---)
CD (Default Value: COAXIAL)
TV (Default Value: OPTICAL)
COAXIAL,
OPTICAL
Assign the COAXIAL terminal or OPTICAL terminal to any
input selector.
• Supported sampling rates for PCM signals (stereo, mono) from a digital input are
32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/16bit, 20bit, and 24bit.
4. Analog Audio Input
Change input assignment between the input selectors and AUDIO IN jacks. If
you do not assign a jack, select "---".
BD/DVD (Default Value: ---)
GAME (Default Value: ---)
CBL/SAT (Default Value: ---)
STRM BOX (Default Value: ---)
PC (Default Value: AUDIO 1)
AUX (Default Value: AUDIO 2)
CD (Default Value: AUDIO 3)
TV (Default Value: ---)
AUDIO 1,
AUDIO 2,
AUDIO 3
Assign the AUDIO IN terminal to any input selector.
96
SetupSetup
2. Speaker2. Speaker
1. Conguration
Change the settings of connection environment of the speakers.
Speaker Channels (Default Value: 7.1 ch)
Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch", "6.1 ch", "7.1 ch", "2.1.2 ch",
"3.1.2 ch", "4.1.2 ch", or "5.1.2 ch" to suit the number of speaker channels
connected.
Subwoofer (Default Value: Yes)
Set whether a subwoofer is connected or not.
Yes When a subwoofer is connected
No When a subwoofer is not connected
Height Speaker (Default Value: Top Middle)
Set the speaker type when height speakers are connected. Select from "Top
Middle", "Top Rear", "Rear High", "Dolby Speaker (Front)", "Dolby Speaker
(Surr)", "Front High" and "Top Front" according to the type and layout of the
connected speakers.
• If an item cannot be selected even though connection is correct, check
that the settings in "Speaker Channels" matches the number of connected
channels.
Zone B Speaker (Default Value: No)
Set whether speakers are connected to ZONE B speaker terminals.
• This setting cannot be selected when "Speaker Channels" is set to "6.1 ch",
"7.1 ch", "4.1.2 ch" or "5.1.2 ch".
Yes When speakers are connected to ZONE B speaker terminals
No When speakers are not connected to ZONE B speaker
terminals
• This setting is xed to "No" when "Bi-Amp" is set to "Yes".
Zone B Output Level (Default Value: Fixed)
When audio is output to ZONE B, set whether the volume is adjusted with the
integrated amplier in the separate room or with this unit.
• This setting is xed to "Variable" when "Zone B Speaker" is set to "Yes".
Fixed When adjusting with the integrated amplier in the separate
room
Variable When adjusting with this unit
Bi-Amp (Default Value: No)
Set whether the front speakers are bi-amp connected.
• This setting cannot be selected when surround back speakers or height
speakers are used.
No When front speakers are not bi-amp connected
• This setting is xed to "No" when "Zone B Speaker" is set to
"Yes".
Yes When front speakers are bi-amp connected
Speaker Impedance (Default Value: 6ohms or above)
Set the impedance (Ω) of the connected speakers.
• For impedance, check the indications on the back of the speakers or their
instruction manual.
4ohms When any of the connected speakers have 4 Ω or more to less
than 6 Ω impedance
6ohms or above
When all the connected speakers have an impedance of 6 Ω
or more
97
SetupSetup
2. Speaker
2. Crossover
Change the settings of crossover frequencies.
Front (Default Value: 100 Hz)
Center (Default Value: 100 Hz)
Height (Default Value: 100 Hz)
Surround (Default Value: 100 Hz)
Surround Back (Default Value: 100 Hz)
LPF of LFE (Default Value: 120 Hz)
Double Bass (Default Value: On)
Front:
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting
frequencies for each channel.
"Full Band": Full band will be output.
• If "Conguration" - "Subwoofer" is set to "No", "Front" is xed to "Full Band",
and the low pitched range of the other channels is output from the front
speakers. Refer to the instruction manual of your speakers to make the
setting.
Center, Height, Surround:
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting
frequencies for each channel.
"Full Band": Full band will be output.
• "Full Band" can be selected only when "Front" is set to "Full Band".
• If the item cannot be selected even though connection is correct, check if
the setting in "Conguration" - "Speaker Channels" matches the number of
connected channels.
Surround Back:
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting
frequencies for each channel.
"Full Band": Full band will be output.
• "Full Band" can be selected only when "Surround" is set to "Full Band".
• If the item cannot be selected even though connection is correct, check if
the setting in "Conguration" - "Speaker Channels" matches the number of
connected channels.
LPF of LFE:
Set the low-pass lter for LFE (low-frequency eect) signals in order to pass
only the lower frequency signals than the set value, and thus cancel unwanted
noises. The low-pass lter is eective only on sources with LFE channel.
The value from "80 Hz" to "120 Hz" can be set.
"O": When this function is not used
Double Bass:
This can be selected only when "Conguration" - "Subwoofer" is set to "Yes"
and "Front" is set to "Full Band".
Boost bass output by feeding bass sounds from the front left and right
speakers and the center speaker to the subwoofer.
"On": Bass output is boosted.
"O": Bass output is not boosted.
• This function is not automatically set even if AccuEQ Room Calibration is
performed.
98
SetupSetup
2. Speaker
3. Distance
Set the distance from each speaker to the listening position.
Front Left (Default Value: 12.0 ft/3.60 m)
Center (Default Value: 12.0 ft/3.60 m)
Front Right (Default Value: 12.0 ft/3.60 m)
Height Left (Default Value: 9.0 ft/2.70 m)
Height Right (Default Value: 9.0 ft/2.70 m)
Surround Right (Default Value: 7.0 ft/2.10 m)
Surr Back Right (Default Value: 7.0 ft/2.10 m)
Surr Back Left (Default Value: 7.0 ft/2.10 m)
Surround Left (Default Value: 7.0 ft/2.10 m)
Subwoofer (Default Value: 12.0 ft/3.60 m)
• The unit of distance can be changed by pressing the MODE button on the
remote controller. When using the unit "feet", the setting is available in
increments of 0.1 ft from 0.1 ft to 30.0 ft. When using the unit "meter", the
setting is available in increments of 0.03 m from 0.03 m to 9.00 m.
(Height Left, Height Right):
• This setting cannot be changed when "Conguration" - "Speaker Channels"
is set to "4.1.2 ch" or "5.1.2 ch", and the audio output destination is set to "On
(A+B)".
(Surr Back Right, Surr Back Left):
• This setting cannot be changed when the audio output destination is set to
"On (A+B)" or "On (B)".
4. Level Calibration
Adjust the volume level of each speaker.
• This setting cannot be selected when the audio output destination is set to
"On (B)".
Front Left (Default Value: 0.0 dB)
Center (Default Value: 0.0 dB)
Front Right (Default Value: 0.0 dB)
Height Left (Default Value: 0.0 dB)
Height Right (Default Value: 0.0 dB)
Surround Right (Default Value: 0.0 dB)
Surr Back Right (Default Value: 0.0 dB)
Surr Back Left (Default Value: 0.0 dB)
Surround Left (Default Value: 0.0 dB)
Subwoofer (Default Value: 0.0 dB)
Select a value between "-12.0 dB" and "+12.0 dB" ("-15.0 dB" and "+12.0 dB"
for Subwoofer) (in 0.5 dB increments). A test tone will be output each time you
change the value. Select the desired level.
(Height Left, Height Right):
• This setting cannot be changed when "Conguration" - "Speaker Channels"
is set to "4.1.2 ch" or "5.1.2 ch", and the audio output destination is set to "On
(A+B)".
(Surr Back Right, Surr Back Left):
• This setting cannot be changed when the audio output destination is set to
"On (A+B)".
99
SetupSetup
2. Speaker
5. Dolby Enabled Speaker
Change the settings of Dolby Enabled Speakers.
• This setting can be selected when "Conguration" - "Height Speaker" is set to
"Dolby Speaker".
Distance from the ceiling (Default Value: 6.0 ft/1.80 m)
Set the distance between the Dolby Enabled Speaker and the ceiling. Select
between "0.1 ft"/"0.03 m" and "15.0 ft"/"4.50 m" ("0.1 ft"/"0.03 m" units).
• The unit of distance (ft/m) is displayed using the unit selected for the
"Distance" setting.
AccuReex (Default Value: O)
You can enhance the reection eect of Dolby Enabled Speakers from the
ceiling.
O When this function is not used
On When this function is used
6. Equalizer Settings
You can adjust the output volume of the range for each connected speaker.
Adjust the volume of dierent sound ranges for each speaker. You can set three
dierent equalizers in Preset 1 to 3. The number of frequencies that can be
selected for each speaker is up to ve bands for the Subwoofer and nine bands
for the other speakers.
Front (Default Value: 0.0dB)
Center (Default Value: 0.0dB)
Height (Default Value: 0.0dB)
Surround (Default Value: 0.0dB)
Surround Back (Default Value: 0.0dB)
Subwoofer (Default Value: 0.0dB)
After selecting the speaker frequency from between "25 Hz" and "16 kHz" ("25
Hz" and "160 Hz" for Subwoofer) with the cursors / , adjust the volume of that
frequency between "-6.0 dB" and "+6.0 dB" with / .
• Depending on the input source or listening mode setting, the desired eect
may not be achieved.
(Subwoofer):
• This cannot be selected if "Conguration" - "Subwoofer" is set to "No".
100
SetupSetup
2. Speaker
7. Speaker Virtualizer
The Speaker Virtualizer function can be switched between On and O.
Speaker Virtualizer (Default Value: On)
On Listening modes such as T-D that have virtual speaker eects
can be selected.
O Listening modes such as T-D that have virtual speaker eects
cannot be selected.
101
SetupSetup
3. Audio Adjust3. Audio Adjust
1. Multiplex/Mono
Change the settings of multiplex audio playback.
Multiplex Input Channel (Default Value: Main)
Set the audio channel or language to be output when playing multiplex audio or
multilingual broadcasts, etc.
• For multiplex audio broadcasts, pressing the
button on the remote
controller will display "1+1" on the main unit’s display.
Main Main channel only
Sub Sub channel only
Main / Sub Main and sub channels will be output at the same time.
Mono Input Channel (Default Value: Left + Right)
Set the input channel when playing back analog or 2 ch PCM signals in the
Mono listening mode.
Left Left channel only
Right Right channel only
Left + Right Left and right channels
2. Dolby
Change the setting of when Dolby signals are input.
Loudness Management (Default Value: On)
When playing Dolby TrueHD, enable the dialog normalization function which
keeps the volume of dialog at a certain level. Note that when this setting is O,
the Late Night function that allows you to enjoy surround at low volumes is xed
to o when playing Dolby Digital Plus/Dolby TrueHD.
On When this function is used
O When this function is used
Center Spread (Default Value: O)
Adjust the width of the front sound eld created when playing back with the
Dolby Audio - Surr listening mode.
• Depending on the speaker settings, "O" is applied.
On The sound eld is spread to left and right.
O The sound eld is centralized.
102
SetupSetup
3. Audio Adjust
3. DTS
Change the setting of when DTS signals are input.
DTS Auto Surround (Default Value: On)
When inputting DTS signals that include extended channel information, the
optimum listening mode is automatically selected according to the extended
information contained in the input signal and the speaker conguration of this
unit when playing in the straight decoding listening mode.
On When this function is used
O Audio is played using the same amount of channels in the
input signal according to the speaker conguration of this unit.
• If this function is set to "O", the ES Matrix and ES Discrete
listening modes cannot be selected.
Dialog Control (Default Value: 0 dB)
You can increase the volume of dialog portion of the audio up to 6 dB by 1 dB
step so that you can hear the dialog easily in noisy atmosphere.
• This cannot be set for content other than DTS:X.
• Depending on the content, this function may not be selected.
4. LFE Level
Set the low-frequency eect (LFE) level for Dolby Digital series, DTS series,
Multichannel PCM, and DSD signals.
LFE Level (Default Value: 0 dB)
Select the low-frequency eect (LFE) level of each signal from "0 dB" to "-∞
dB". If the low-frequency eect sound is too strong, select "-20 dB" or "-∞ dB".
5. Volume
Change the Volume settings.
Mute Level (Default Value: -∞ dB)
Set the volume lowered from the listening volume when muting is on. Select a
value from "-∞ dB", "-40 dB", and "-20 dB".
Maximum Volume (Default Value: O)
Set the maximum value to prevent the volume from becoming too loud. Select
a value from "O", and "50" to "99".
Power On Volume (Default Value: Last)
Set the volume level of when the power is turned on. Select a value from "Last"
(Volume level before entering standby mode), "Min", "0.5" to "99.5" and "Max".
• You cannot set a higher value than that of "Maximum Volume".
Headphone Level (Default Value: 0.0 dB)
Adjust the output level of headphones. Select a value between "-12.0 dB" and
"+12.0 dB".
103
SetupSetup
4. Source4. Source
1. My Input Volume
Set a volume value for each input selector.
My Input Volume (Default Value: Last)
Select a value from "Last", "Min", "0.5" to "81.5" and "Max".
• The volume level when the power is turned on is the value set for "Power On
Volume".
• To set the volume to the current volume, press the button of the input
selector you wish to set for approx. 3 seconds.
2. Name Edit
Set an easy name for each input. The set name appears on the main unit’s
display. Select the input selector to make the setting.
Name Edit (Default Value: Input name)
1. Select a character or symbol with the cursors, and press ENTER.
Repeat this operation to input up to 10 characters.
"A/a": Switches between upper and lower cases. (Pressing MODE on the
remote controller also toggles between upper and lower cases)
"←" "→": Moves the cursor in the arrow direction.
" ": Removes a character on the left of the cursor.
" ": Enters a space.
• Pressing CLEAR on the remote controller will remove all the input
characters.
2. After inputting, select "OK" with the cursors, and press ENTER.
The input name will be saved.
To restore the name to the default value, press CLEAR on the remote
controller on the input screen. Then while nothing is entered, select "OK", and
press ENTER.
• To name a preset radio station, press TUNER on the remote controller, select
AM/FM and select the preset number.
• This cannot be set if the "NET" or "BLUETOOTH" input is selected.
Audio Select
Select the priority for input selection when multiple audio sources are connected
to one input selector, such as connections to both the "BD/DVD" HDMI IN jack
and the "BD/DVD" AUDIO IN jack. The setting can be separately set to each
input selector button. Select the input selector to congure. Note that there are
some default values you cannot change.
BD/DVD (Default Value: HDMI)
GAME (Default Value: HDMI)
CBL/SAT (Default Value: HDMI)
STRM BOX (Default Value: HDMI)
PC (Default Value: Analog)
AUX (Default Value: Analog)
CD (Default Value: COAXIAL)
TV (Default Value: OPTICAL)
ARC When giving priority to input signal from ARC compatible TV.
• The setting can be selected only when "5. Hardware" -
"HDMI" - "Audio Return Channel (eARC supported)" is set to
"On" and also the "TV" input is selected.
HDMI When giving priority to input signal from HDMI IN jacks
• This item can be selected only when the input to be set is
assigned to the HDMI jack in the "1. Input/Output Assign" -
"HDMI Input" setting.
COAXIAL When giving priority to input signal from DIGITAL IN COAXIAL
jacks
• This item can be selected only when the input to be set
is assigned to the COAXIAL jack in the "1. Input/Output
Assign" - "Digital Audio Input" setting.
OPTICAL When giving priority to input signal from DIGITAL IN OPTICAL
jacks
• This item can be selected only when the input to be set
is assigned to the OPTICAL jack in the "1. Input/Output
Assign" - "Digital Audio Input" setting.
104
SetupSetup
4. Source
Analog When giving priority to the input signal from AUDIO IN jacks
• This item can be selected only when the input to be set
is assigned to the AUDIO IN jack in the "1. Input/Output
Assign" - "Analog Audio Input" setting.
PCM Fixed Mode (Default Value: O)
Select whether to x input signals to PCM (except multi-channel PCM) when
you select "HDMI", "COAXIAL", or "OPTICAL" in the "Audio Select" setting. Set
this item to "On" if noise is produced or truncation occurs at the beginning of a
track when playing PCM sources. Select "O" normally.
• Each time the "Audio Select" setting is changed, the setting is restored to
"O ".
• The setting cannot be changed when "TUNER", "NET", or "BLUETOOTH"
input is selected.
Video Select
When "TUNER", "NET", or "BLUETOOTH" input is selected, you can set the
input from which video is displayed on the TV.
Video Select (Default Value: Last)
Last Select the video input played immediately prior.
BD/DVD,
GAME,
CBL /SAT,
STRM BOX,
PC,
CD,
TV
Play the video of each input.
• This setting is eective for an input selector assigned in
"1. Input/Output Assign" - "HDMI Input".
105
SetupSetup
5. Hardware5. Hardware
1. HDMI
Change the settings of the HDMI function.
HDMI CEC (Default Value: On)
Setting this to "On" enables the input selection link and other link functions with
HDMI-connected CEC-compatible device.
When this setting is changed, turn o and then on again the power of all
connected devices.
• Depending on the TV to use, a link setting may be required on the TV.
• This function is eective only when the device is connected to the HDMI OUT
MAIN terminal.
• Setting this to "On" and closing the operation screen will display the name
of the connected CEC-compatible device and "CEC On" on the main unit’s
display.
• When this function is set to "On", the power consumption in standby state
increases, however, the increase in power consumption is minimized by
automatically entering the HYBRID STANDBY mode where only the essential
circuits operate.
• If you operate the MASTER VOLUME dial on the main unit when this setting is
"On" and audio is output from the TV speakers, audio will be output also from
the speakers connected to this unit. To output audio from only either of them,
change the setting of this unit or TV, or reduce the volume of this unit.
• If abnormal behavior is observed when this is set to "On", set it to "O".
• If a connected device is not CEC-compatible, or if you are not sure whether it
is compatible, set it to "O".
On When this function is used
O When this function is not used
HDMI Standby Through (Default Value: Auto (Eco))
When this is set to anything other than "O", you can play the video and audio of
an HDMI-connected player on the TV even if the unit is in standby mode. Also,
only "Auto" and "Auto (Eco)" can be selected if "HDMI CEC" is set to "On". If you
select anything else, set "HDMI CEC" to "O".
• When this function is set to a value other than "O", the power consumption
in standby state increases, however, the increase in power consumption is
minimized by automatically entering the HYBRID STANDBY mode where only
the essential circuits operate.
• To play a non-CEC compliant player on the TV, turn the unit on and switch the
input.
• When using a CEC-compliant TV, you can reduce the power consumption in
standby mode by selecting "Auto (Eco)".
O When this function is not used
BD/DVD,
GAME,
CBL /SAT,
STRM BOX,
PC,
CD,
TV
For example, if you select "BD/DVD", you can play the
equipment connected to the "BD/DVD" jack on the TV even
if the unit is in standby mode. Select this setting if you have
decided which player to use with this function.
Last You can play on the TV the video and audio of the input
selected immediately before the unit is switched to standby.
When "Last" is selected, you can switch the input of the unit
using the remote controller or the Onkyo Controller even in the
standby mode.
Auto,
Auto (Eco)
Select one of these settings when you have connected
equipment that conforms to the CEC standard. You can
play the video and audio of the input selected on the TV,
irrespective of what input was selected immediately prior to the
unit being switched to standby, using the CEC link function.
106
SetupSetup
5. Hardware
Audio TV Out (Default Value: Auto)
You can enjoy audio through the speakers of the TV while this unit is on.
• This setting is xed to "Auto" if you set "1. Input/Output Assign" - "TV Out/
OSD" - "HDMI Out" or "HDMI" - "HDMI Out" in the "Quick Menu" to "MAIN"
or "MAIN+SUB" and set "HDMI CEC" to "On". If you change this setting, set
"HDMI CEC" to "O".
• Listening mode cannot be changed while "Audio TV Out" is set to "On" and
audio is being output from the TV.
• Depending on your TV or input signal of the connected device, audio may not
be output from the TV even if this is set to "On". In such a case, audio is output
from the speakers of the unit.
• Audio is output from this unit if you operate the MASTER VOLUME dial on this
unit when audio that is input to this unit is output from your TV speakers. If you
do not want to output audio, change the setting of this unit or TV, or reduce the
volume of this unit.
On When this function is used
O When this function is not used
Auto When the "HDMI Out" setting is "MAIN" or "MAIN+SUB" and
the "HDMI CEC" setting is "On", the setting is xed to "Auto".
With "Auto", when audio is output from the TV speakers, audio
is not output from the speakers of this unit, and when audio is
output from the speakers of this unit, audio is not output from
the TV speakers.
• If the HDMI CEC setting is o on the TV, there may be audio
output from both the TV speakers and the speakers of this
unit.
Audio Return Channel (eARC supported) (Default Value: On)
You can enjoy the sound of an HDMI-connected ARC-compatible TV or eARC-
compatible TV through the speakers connected to the unit.
On When enjoying the TV sound through the speakers connected
to the unit
O When the ARC function or eARC function is not used
Auto Lip Sync (Default Value: On)
Automatically corrects desynchronization between the video and audio signals
based on the information from the HDMI Lip-Sync-compatible TV.
On When enabling the automatic correction function
O When not using the automatic correction function
107
SetupSetup
5. Hardware
2. Network
Change the settings of the Network function.
• When LAN is congured with a DHCP, set "DHCP" to "Enable" to congure
the setting automatically. ("Enable" is set by default) To assign xed IP
addresses to each components, you must set "DHCP" to "Disable", assign an
address to this unit in the "IP Address" setting, and set information related to
your LAN, such as Subnet Mask and Gateway.
Wi-Fi (Default Value: O(Wired))
Connect the unit to the network via a wireless LAN router.
• When switching between "On" and "O(Wired)", stop the Network service.
Also, when group playback is in process, cancel the group playback once, and
then switch the setting.
On Wireless LAN connection
O(Wired) Wired LAN connection
Wi-Fi Setup (Default Value: -)
Congure wireless LAN settings by pressing ENTER with "Start" displayed.
Wi-Fi Status (Default Value: -)
The information of the connected access point is displayed.
SSID SSID of the connected access point.
Signal Signal strength of the connected access point.
Status Status of the connected access point.
MAC Address (Default Value: -)
Check the MAC address of this unit.
This value is specic to the component and cannot be changed.
DHCP (Default Value: Enable)
Enable Auto conguration by DHCP
Disable Manual conguration without DHCP
• If you select "Disable", set "IP Address", "Subnet Mask",
"Gateway", and "DNS Server" manually.
IP Address (Default Value: 0.0.0.0)
Displays/Sets the IP address.
Subnet Mask (Default Value: 0.0.0.0)
Displays/Sets the subnet mask.
Gateway (Default Value: 0.0.0.0)
Displays/Sets the gateway.
DNS Server (Default Value: 0.0.0.0)
Displays/Sets the primary DNS server.
Proxy URL (Default Value: -)
Displays/Sets the proxy server URL.
Proxy Port (Default Value: 8080)
Displays/Sets the proxy server port number when you input "Proxy URL".
108
SetupSetup
5. Hardware
Friendly Name (Default Value: Onkyo TX-NR5100 XXXXXX)
Change the model name of this unit which is displayed on the device
connected to the network to an easily recognized name.
1. Press ENTER to display the Edit screen.
2. Select a character or symbol with the cursors, and press ENTER.
Repeat this operation to input up to 31 characters.
"A/a": Switches between upper and lower cases. (Pressing MODE on the
remote controller also toggles between upper and lower cases)
"←" "→": Moves the cursor in the arrow direction.
" ": Removes a character on the left of the cursor.
" ": Enters a space.
• Pressing CLEAR on the remote controller will remove all the input
characters.
3. After inputting, select "OK" with the cursors, and press ENTER.
The input name will be saved.
AirPlay (Default Value: On)
Select whether or not to use the AirPlay function.
On When this function is used
O When this function is not used
AirPlay Device Name (Default Value: Onkyo TX-NR5100 XXXXXX)
Change the model name of this unit which is displayed on the AirPlay-
connected device to an easily recognized name.
1. Press ENTER to display the Edit screen.
2. Select a character or symbol with the cursors, and press ENTER.
Repeat this operation to input up to 31 characters.
"A/a": Switches between upper and lower cases. (Pressing MODE on the
remote controller also toggles between upper and lower cases)
"←" "→": Moves the cursor in the arrow direction.
" ": Removes a character on the left of the cursor.
" ": Enters a space.
• Pressing CLEAR on the remote controller will remove all the input
characters.
3. After inputting, select "OK" with the cursors, and press ENTER.
The input name will be saved.
• This function cannot be used when registering this unit to Home App.
109
SetupSetup
5. Hardware
AirPlay Password (Default Value: -)
You can set a password of up to 31 characters so that only users that have
input can use AirPlay.
1. Press ENTER to display the Edit screen.
2. Select a character or symbol with the cursors, and press ENTER.
Repeat this operation to input up to 31 characters.
"A/a": Switches between upper and lower cases. (Pressing MODE on the
remote controller also toggles between upper and lower cases)
"←" "→": Moves the cursor in the arrow direction.
" ": Removes a character on the left of the cursor.
" ": Enters a space.
• To select whether to mask the password with "" or display it in plain text,
press MEMORY on the remote controller.
• Pressing CLEAR on the remote controller will remove all the input
characters.
3. After inputting, select "OK" with the cursors, and press ENTER.
The input password will be saved.
• This function cannot be used when registering this unit to Home App.
Privacy Statement (Default Value: Not Accepted)
When using a network service that requires a login name, email address,
password, etc., you need to agree to the Privacy Statement of our company.
• This setting can be made after conrming the Privacy Statement. When
you select "Privacy Statement" and press ENTER, the Privacy Statement is
displayed.
• When "Not Accepted" is selected, you will log out from the network service
you have logged in.
Network Check (Default Value: -)
You can check the network connection.
Press ENTER when "Start" is displayed.
• Wait for a while if "Network" cannot be selected. It can be selected when the
network function is activated.
110
SetupSetup
5. Hardware
3. Bluetooth
Change the settings for the BLUETOOTH function.
• Wait for a while if "Bluetooth" cannot be selected. It can be selected when the
BLUETOOTH function is activated.
(Bluetooth Receiver)
Bluetooth Receiver (Default Value: On)
Select whether or not to use the function that receives audio from BLUETOOTH
wireless technology enabled devices.
On When this function is used
O When this function is not used
Auto Input Change (Default Value: On)
When a BLUETOOTH enabled device is played while it is connected to the unit,
the input of the unit can be automatically switched to "BLUETOOTH".
On The input will automatically become "BLUETOOTH" when a
BLUETOOTH enabled device is connected.
O The function is disabled.
• If the input is not switched automatically, set this to "O", and
change the input manually.
Auto Reconnect (Default Value: On)
This function automatically reconnects to the BLUETOOTH enabled device
connected last when you change the input to "BLUETOOTH".
• This may not work with some BLUETOOTH enabled devices.
On When this function is used
O When this function is not used
Pairing Information (Default Value: -)
You can initialize the pairing information stored on this unit. If you are no longer
able to connect with a device you have paired, try doing this. ( →p129)
Pressing ENTER when "Clear" is displayed initializes the pairing information
stored on this unit.
• This function does not initialize the pairing information on the BLUETOOTH
enabled device. When pairing the unit again with the device, be sure to clear
the pairing information on the BLUETOOTH enabled device beforehand. For
information on how to clear the pairing information, refer to the instruction
manual of the BLUETOOTH enabled device.
Device (Default Value: -)
Displays the name of the BLUETOOTH enabled device connected to the unit.
• The name is not displayed when "Status" is "Ready" and "Pairing".
Status (Default Value: -)
Displays the status of the BLUETOOTH enabled device connected to the unit.
Ready Not paired
Pairing Paired
Connected Successfully connected
(Bluetooth Transmitter)
Bluetooth Transmitter (Default Value: O)
Select whether or not to use the function that transmits audio from this unit to
BLUETOOTH wireless technology enabled devices.
On ( Tx) When this function is to be used (played back only on
Bluetooth wireless technology enabled devices)
On
(Main + Tx)
When this function is to be used (played back both on this unit
and on Bluetooth wireless technology enabled devices)
O When this function is not used
111
SetupSetup
5. Hardware
Search Devices (Default Value: -)
Search for a BLUETOOTH wireless technology enabled device that is able to
receive the audio from this unit. Select "Start" then press ENTER. A list of the
names of BLUETOOTH wireless technology enabled devices that are able to
receive is displayed. Select the device to be connected with the cursors / ,
then pairing begins when you press ENTER.
Output Level (Default Value: Variable)
You can select whether to adjust the volume on this unit or to adjust it on the
Bluetooth wireless technology enabled device.
Variable To use the volume controls on this unit
Fixed To use the volume controls on the Bluetooth wireless
technology enabled device
aptX HD (Default Value: O)
It is possible to use aptX HD to connect a BLUETOOTH wireless technology
enabled device and this unit.
• The codec of the receiving device must be compatible with aptX HD.
On When this function is used
O When this function is not used
Low Latency Mode (Default Value: O)
If the audio from a device connected via BLUETOOTH is delayed compared to
the video on the TV when watching a gaming screen, etc., you can reduce the
audio delay.
On When this function is used
O When this function is not used
Pairing Information (Default Value: -)
You can initialize the pairing information stored on this unit. If you are no longer
able to connect with a device you have paired, try doing this. ( →p130)
Pressing ENTER when "Clear" is displayed initializes the pairing information
stored on this unit.
• This function does not initialize the pairing information on the BLUETOOTH
enabled device. When pairing the unit again with the device, be sure to clear
the pairing information on the BLUETOOTH enabled device in advance. For
information on how to clear the pairing information, refer to the BLUETOOTH
enabled device's instruction manual.
Device (Default Value: -)
Displays the name of the BLUETOOTH enabled device connected to the unit.
• The name is not displayed when "Status" is "Ready" and "Pairing".
Status (Default Value: -)
Displays the status of the BLUETOOTH enabled device connected to the unit.
Ready Not paired
Pairing Paired
Connected Successfully connected
Connected
(aptX)
Successfully connected with aptX compatible device
Connected
(aptX HD)
Successfully connected with aptX HD compatible device
112
SetupSetup
5. Hardware
4. Power Management
Change the settings for the power-save function.
Sleep Timer (Default Value: O)
30 minutes,
60 minutes,
90 minutes
You can allow the unit to enter standby automatically when the
specied time has elapsed. Select a value from "30 minutes",
"60 minutes" and "90 minutes".
O Does not turn the unit to standby automatically.
Auto Standby (Default Value: O)
This setting allows the unit to enter standby mode automatically after 20
minutes of inactivity without any video or audio input. (When "USB Power Out
at Standby" or "Network Standby" is enabled, the unit enters the HYBRID
STANDBY mode which minimizes the increase in power consumption.)
On The unit will automatically enter standby mode ("AUTO STBY"
will light).
• "Auto Standby" is displayed on the main unit’s display and
TV screen 30 seconds before entering standby mode.
O The unit will not automatically enter standby mode.
Auto Standby in HDMI Standby Through (Default Value: O)
Enable or disable "Auto Standby" while "HDMI Standby Through" is on.
On The setting will be enabled.
• This setting cannot be set to "On" if "Auto Standby" and
"HDMI Standby Through" are set to "O".
O The setting will be disabled.
USB Power Out at Standby (Default Value: O)
Devices connected to the USB port (5 V/1 A) on the rear of the unit can be
supplied with electricity even when this unit is in standby mode when this
function is "On".
• When this function is set to "On", the power consumption in standby state
increases, however, the increase in power consumption is minimized
by automatically entering the HYBRID STANDBY mode where only the
essential circuits operate.
Network Standby (Default Value: On)
When this function is set to "On", the network function works even in standby
state, and you can turn on the power of the unit via network using an
application such as Onkyo Controller that can control this unit.
• When this function is set to "On", the power consumption in standby state
increases, however, the increase in power consumption is minimized
by automatically entering the HYBRID STANDBY mode where only the
essential circuits operate. Note that even if this function is set to "O", when
any of the HDMI CEC ( →p105), HDMI Standby Through ( →p105),
USB Power Out at Standby ( →p112) and Bluetooth Wakeup ( →p113)
functions is enabled, this function will be in "On" state regardless of the
setting.
• When connection to the network is lost, "Network Standby" may be disabled
to reduce power consumption. In such a case, turn the unit on by using the
power button on the remote controller or main unit.
113
SetupSetup
5. Hardware
Bluetooth Wakeup (Default Value: O)
This function wakes up the unit on standby by connecting a BLUETOOTH
enabled device.
On When this function is used
• When this function is set to "On", the power consumption
in standby state increases, however, the increase in power
consumption is minimized by automatically entering the
HYBRID STANDBY mode where only the essential circuits
operate.
O When this function is not used
• This setting is xed to "O" if "Bluetooth" -"Bluetooth
Receiver" is set to "O".
• This setting is also xed to "O" if "Bluetooth" - "Bluetooth
Receiver" - "Auto Input Change" is set to "O".
• Wait for a while if "Network Standby" and "Bluetooth Wakeup" cannot be
selected. It can be selected when the network function is activated.
5. Works with SONOS
Change the settings to connect with the Sonos Connect.
Input Selector (Default Value: O)
Select the input selector to which the Sonos Connect is connected.
• Selecting "O" disables the interlock function with Sonos.
Connected Device (Default Value: -)
Displays the Sonos Connect connected to the same network as the network of
this unit. Press the ENTER button to select the connected Sonos Connect.
• Products (e.g. Play:3 unequipped with an output terminal) other than the
Sonos Connect are also displayed in the device list and selectable. In
that case, when playback on the Sonos side starts, the input is switched,
however, audio is not output. Select the room name of the connected Sonos
Connect.
• Up to 32 devices can be displayed on the Sonos product list screen. If you
cannot nd the Sonos Connect to be interlocked, return to the previous
screen, turn o the product you do not want to interlock, and try again.
• To use this function, set "Input Selector" beforehand.
Preset Volume (Default Value: Main=Last)
You can set the volume beforehand for playing back the Sonos Connect.
Select a value from "Last" (Volume level before entering standby mode), "Min",
"0.5" to "99.5" and "Max".
• To use this function, set "Input Selector" beforehand.
114
SetupSetup
6. Miscellaneous6. Miscellaneous
1. Tuner
Change the settings for Tuner.
AM / FM Frequency Step (Default Value: 10 kHz / 0.2 MHz)
Select a frequency step to suit your residential area.
Select "10 kHz/0.2 MHz" or "9 kHz/0.05 MHz".
• When this setting is changed, all radio presets are deleted.
2. Remote ID
Change the remote controller ID.
Remote ID (Default Value: 1)
If multiple ONKYO products are installed in the same room, select the ID
for the remote control used with this unit from "1", "2" and "3" to prevent
interference between the unit and other ONKYO products. After changing the
ID on the main unit, set the same ID on the remote controller as the main unit
with the following procedure.
While pressing and holding the MODE button, press the following buttons for
approx. 3 seconds.
• To change the remote controller ID to "1": MOVIE/TV
• To change the remote controller ID to "2": MUSIC
• To change the remote controller ID to "3": GAME
115
SetupSetup
6. Miscellaneous
3. Firmware Update
Change the settings for Firmware Update.
Update Notice (Default Value: Enable)
Availability of a rmware update is notied via network.
Enable Notify updates
Disable Do not notify updates
Version (Default Value: -)
The current rmware version is displayed.
Update via NET (Default Value: -)
Press ENTER to select when updating the rmware via network.
• This setting cannot be selected if you do not have Internet access or there is
no updatable rmware.
Update via USB (Default Value: -)
Press ENTER to select when updating the rmware via USB.
• This setting cannot be selected if a USB storage device is not connected or
there is no updatable rmware in the USB storage device.
• Wait for a while if "Firmware Update" cannot be selected. It can be selected
when the network function is activated.
4. Initial Setup
Make the initial setup from the setup menu.
• Wait for a while if "Initial Setup" cannot be selected. It can be selected when
the network function is activated.
5. Lock
Lock the Setup menu so that the settings cannot be changed.
Setup Parameter (Default Value: Unlocked)
Lock the Setup menu so that the settings cannot be changed.
Locked The menu is locked.
Unlocked The menu is unlocked.
6. Factory Reset
All the settings are restored to factory defaults.
Factory Reset (Default Value: -)
All the settings are restored to factory defaults.
Select "Start" and press ENTER.
• If "Factory Reset" is performed, your settings are restored to the default
values. Be sure to note down your setting contents beforehand.
116
Setup
Web Setup
Menu operations
You can make the settings for the network function of this unit using an Internet
browser on a PC, smartphone, etc.
1. Press
on the remote controller to display the Setup menu.
2. Select "5. Hardware" - "Network" with the cursors, and then take a note of the
IP address displayed in "IP Address".
3. Start the Internet browser on your PC, smartphone, etc. and enter the IP
address of this unit in the URL eld.
4. The screen for entering the user name and password is displayed. Enter the
following then click "OK".
User name: admin (xed)
Password: admin (default value)
• You can change the password after logging in.
• Input is required again if you close the browser.
• Take a note of the password so that you do not forget it. If you do forget
it, reset the unit "Resetting the unit (this resets the unit settings to the
default)" ( →p123) then log in again with the initial settings (admin).
5. Information for the unit (Web Setup screen) is displayed in the internet
browser.
6. After changing the settings, select "Save" to save the settings.
Device Information
You can change the Friendly Name or AirPlay Device Name, set an
AirPlay Password, etc.
Control4: Register this unit if you are using a Control4 system.
Firmware Update: Select the rmware le you have downloaded to your PC so
you can update this unit.
Network Setting
Status: You can see information for the network such as the MAC address and
IP address of this unit.
Network Connection: You can select a network connection method. If you select
"Wireless", select an access point from "Wi-Fi Setup" to connect.
DHCP: You can change DHCP settings. If you select "O", set "IP Address",
"Subnet Mask", "Gateway" and "DNS Server" manually.
Proxy: Display and set the URL for the proxy server.
117
Setup
Initial Setup with Auto Start-up Wizard
Operations
When you turn the unit on for the rst time after purchase, the Initial Setup
screen is automatically displayed on the TV to allow you to make settings
required for startup using simple operations following on-screen guidance.
1. Switch the input of the TV to the input connected to the unit.
2. Put batteries into the remote controller of this unit.
3. Press on the remote controller to turn the unit on.
4. When the language selection screen is displayed on TV, select the language
with the cursors
/ and press ENTER.
5. To make the network connection settings, select "Yes" and press ENTER.
• Select the item with the cursors of the remote controller, and press ENTER to
conrm your selection. To return to the previous screen, press
.
• If you have terminated the Initial Setup halfway, turn this unit to standby mode
and turn the power on again. Then you can display the Initial Setup again.
Unless you do the Initial Setup to the end or select "Never Show Again" in
the screen shown after setting the Network Connection, the wizard screen is
shown every time the power is turned on.
• To perform the Initial Setup again after the setting is completed, press ,
select "6. Miscellaneous" - "Initial Setup", and press ENTER.
CLEAR
MEMORY
/ / /
ENTER
Inputs
TV
HDMI 1
HDMI 2
HDMI 3
TV
INPUT
TV’s REMOTE
118
Setup
Network Connection
1. A conrmation screen asking you whether to agree to the privacy statement
is displayed during network setting. If you agree, select "Accept" and press
ENTER.
2. Select the type of connection to the network. To use the Chromecast built-in
function to connect, select "Yes" and press ENTER. The Google Home app is
required to use the Chromecast built-in function. Download the Google Home
app from Google Play or the App Store to your smart phone or tablet.
• Google Home app can be used on the following operating systems. (As of
february 2021)
Android™: Android 6.0 or later.
iOS: iOS 12.0 or later. Compatible with iPhone
®
, iPad
®
, and iPod touch
®
.
111 2
22
If you select "No", you can connect using either wired LAN or Wi-Fi.
"Wired": Use a wired LAN to connect to a network.
"Wireless": Wi-Fi connection using an access point such as a wireless LAN
router.
• There are two methods for Wi-Fi connection.
"Scan Networks": Search for an access point from this unit. Find out the
SSID of the access point beforehand.
"Use iOS Device (iOS7 or later)": Share the Wi-Fi settings of your iOS
device with this unit.
• If you select "Scan Networks", there are another two types of connection
methods. Check the following.
"Enter Password": Enter the password (or key) of the access point to
connect.
"Push Button": If the access point is equipped with an automatic setting
button, you can connect without entering the password.
• If the SSID of the access point is not displayed, select "Other..." with the
cursor on the SSID list screen, press ENTER, and then follow the on-
screen instructions.
Keyboard Input
To switch between upper and lower cases, select "A/a" on the screen, and press
ENTER on the remote controller.
To select whether to mask the password with "" or display it in plain text, press
MEMORY on the remote controller. Pressing CLEAR on the remote controller
will delete all the input characters.
1. Speaker Setup
1. Select the connected speaker conguration and press ENTER.
Note that the image on the screen changes each time you select the number
of channels in "Speaker Channels".
Speaker Setup
Speaker Channels
Subwoofer
Height Speaker
ZoneB Speaker
ZoneB Output Level
Bi-Amp
Speaker Impedance
Select how many speakers you have.
Next
7.1 ch
< >
Yes
---
No
Fixed
No
6ohms or above
1
2
3
4
5
6
7
1 Select to suit the number of speaker channels connected.
2 Set whether a subwoofer is connected or not.
3 Set the speaker type if height speakers are connected to the HEIGHT
terminals.
4 Set whether speakers are connected to Zone B speaker terminals.
5 When audio is output to ZONE B, set whether the volume is adjusted with the
integrated amplier in the separate room or with this unit.
6 Set whether the front speakers are bi-amp connected.
7 Set the impedance of the connected speakers.
2. The speaker combination selected in step 1 is displayed. "Yes" is displayed
for the selected speakers. If the setting is correct, press ENTER.
3. Select "Next" and press ENTER. Then a test tone is output from each
speaker to conrm the connection. Selecting each speaker with the cursors
/ will output the test tone. Press ENTER after conrmation.
4. If there is no problem with the speaker connection, select "Next" and press
ENTER. To return to "Speaker Setup", select "Back to Speaker Setup" and
119
Setup
press ENTER.
2. ARC Setup
If you have connected a TV that supports ARC, select "Yes" and press ENTER.
3. AccuEQ Room Calibration
Place the supplied speaker setup microphone at the listening position. The unit
automatically measures the test tones output from each speaker, and sets the
optimum volume level for each speaker, the crossover frequencies, and the
distance from the listening position. This also reduces the eect of the standing
wave in accordance with the viewing environment and automatically adjusts the
equalizers for the speakers, and enables correction of sound distortion caused
by the acoustic environment of the room.
• It takes between 3 and 12 minutes for calibration to be completed. Each
speaker outputs the test tone at high volume during measurement, so be
careful of your surroundings. Also, keep the room as quiet as possible during
measurement.
• If you connect a subwoofer, check the power and volume of the subwoofer.
Set the subwoofer volume to more than half.
• If the power of this unit suddenly turns o, the wires in the speaker cables
have touched the rear panel or other wires, and the protection circuit is
working. Twist the wires again securely, and make sure they do not stick out
of the speaker terminals when connecting.
1. Place the supplied speaker setup microphone at the listening position, and
connect it to the SETUP MIC jack on the main unit.
SETUP MI
C
When placing the speaker setup microphone on a tripod, refer to the
illustration.
2. Conrm a test tone is output from the subwoofer and press ENTER.
3. Press ENTER to output test tones from each speaker, and the connected
speakers and the noise in the surrounding environment are automatically
measured.
4. The measurement results in step 3 are displayed. If there is no problem in
the detection result of the speaker, select "Next" and press ENTER to output
the test tone again to automatically set the settings such as volume level,
crossover frequency, etc., to their optimum. (The test tone is automatically
output when 10 seconds has elapsed without any operation.)
5. When the measurement is completed, the measurement results are
displayed. You can check each setting using the cursors
/ . Select "Save"
and press ENTER to save the settings.
6. Disconnect the speaker setup microphone.
120
Setup
Onkyo Controller (available on iOS and Android™ handsets) is a dedicated app
available for free which allows you to use your handset as a remote controller.
Along with basic operations such as switching input and adjusting the volume,
you can also select a radio station or network service (internet radio or play of a
music le) without looking at the TV.
• To use Onkyo Controller, this unit needs to be connected to the same network
as the mobile device.
Main features
• Turning the power on/o, switching input, adjusting the volume, and other
such basic remote controller operations.
• Playing internet radio services (TuneIn Radio, etc.) and selecting stations.
Control in the palm of your hands without looking at the TV.
• Play the music les saved on the mobile device via Wi-Fi.
• Play Amazon Music (compatible models only) ( →p72)
Initial Setup
1. Download the Onkyo Controller from the App Store or Google Play
TM
Store.
2. Connect the mobile device to the same network as the unit.
3. Start Onkyo Controller. This unit is displayed automatically when the app is
started, so tap the unit when displayed to select it.
Onkyo Controller
Troubleshooting
121
Troubleshooting
Troubleshooting
When the unit is operating erratically 123
Try restarting the unit 123
Resetting the unit (this resets the unit settings to the
default) 123
Troubleshooting 124
Power 124
Audio 124
Listening Modes 126
Video 127
Linked operation 128
Tuner 129
BLUETOOTH function 129
Network function 131
USB storage device 132
Wireless LAN Network 132
ZONE B function 133
Remote Controller 133
Display 133
Others 134
122
Troubleshooting
Troubleshooting
Before starting the procedure
Problems may be solved by simply turning the power on/o or disconnecting/
connecting the power cord, which is easier than working on the connection,
setting and operating procedure. Try the simple measures on both the unit and
the connected device. If the problem is that the video or audio is not output or
the HDMI linked operation does not work, disconnecting/connecting the HDMI
cable may solve it. When reconnecting, be careful not to wind the HDMI cable
since if wound the HDMI cable may not t well. After reconnecting, turn o and
on the unit and the connected device.
• The AV receiver contains a microPC for signal processing and control
functions. In very rare situations, severe interference, noise from an external
source, or static electricity may cause it to lockup. In the unlikely event that
this happens, unplug the power cord from the wall outlet, wait at least 5
seconds, and then plug it back in.
• Our company is not responsible for damages (such as CD rental fees) due to
unsuccessful recordings caused by the unit’s malfunction. Before you record
important data, make sure that the material will be recorded correctly.
123
Troubleshooting
When the unit is operating erratically
Try restarting the unit
Restarting this unit may solve the problem. Set the main unit to standby, then
after waiting for 5 seconds or more, press and hold the ON/STANDBY button
of the main unit for at least 5 seconds, and then restart the unit. (The settings
on this unit are kept.) If the problem persists after restarting the unit, unplug and
plug the power cords or HDMI cable of this unit and connected devices.
Resetting the unit (this resets the unit settings to the
default)
If the restart of the unit does not solve the problem, reset the unit, and restore
all the settings to the factory default at the time of purchase. This may solve
the problem. If the unit is reset, your settings are restored to the default values.
Be sure to note down your setting contents before performing the following
operations. Note that it is not possible to reset the unit during the Initial Setup
process. Before doing the following procedures, press to exit Initial Setup.
1. While pressing and holding CBL/SAT of the input selector on the main unit
with the unit turned on, press the
ON/STANDBY button.
2. "Clear" is displayed on the display, and the unit returns to the standby state.
Do not remove the power cord until "Clear" disappears from the display.
To reset the remote controller, while pressing and holding MODE, press the
CLEAR button at least 3 seconds.
1
2
124
Troubleshooting
Troubleshooting
Power
When the power is turned on, "AMP Diag Mode" appears on the display of the main unit
• The protection circuit function may have operated. If the unit suddenly enters the standby state and "AMP Diag Mode" appears on the display
of the main unit when the power is turned on again, this function is diagnosing whether or not the main unit is malfunctioning or there is an
abnormality with the speaker cable connection. When the diagnosis is complete, the following messages are displayed.
CH SP WIRE
If the unit returns to the normal ON state after "CH SP WIRE" appears on the display, the speaker cable may have
been short-circuited. After setting the power of this unit to standby state, connect the speaker cable again. Twist the
wires exposed from the tip of the speaker cable so that the wires do not stick out of the speaker terminal.
NG:
If the operation has stopped with "NG" displayed on the display, set the power of this unit to standby state immediately
and remove the power plug from the outlet. The unit may be malfunctioning. Consult a dealer.
The unit turns o unexpectedly
• If "5. Hardware" - "Power Management" - "Auto Standby" on the Setup menu is activated, the unit automatically enters the standby mode.
• The protection circuit function may have operated due to an abnormal rise in temperature of the unit. In such a case, the power turns o
repeatedly even if the power is turned on each time. Secure sucient ventilation space around the unit, wait for a while until the temperature of
the unit decreases. Then, turn the power on again.
WARNING: If smoke, smell or abnormal noise is produced by the unit, unplug the power cord from the outlet immediately, and contact the dealer or
our company's support.
( →p112)
Audio
• Make sure that the speaker setup microphone is no longer connected.
• Conrm that the connection between the output jack on the connected device and the input jack on this unit is correct.
• Make sure that none of the connecting cables are bent, twisted, or damaged.
• If "MUTING" is displayed on the display and is blinking, press on the remote controller to cancel muting.
• While headphones are connected to the PHONES jack, no sound is output from the speakers.
• When "4. Source" - "Audio Select" - "PCM Fixed Mode" on the Setup menu is set to "On", audio is not played if signals other than PCM are input.
Change the setting to O.
Check the following if the problem persists after you have conrmed the above.
125
Troubleshooting
No sound from the TV
• Change the input selector on this unit to the position of the terminal to which the TV is connected.
• If the TV does not support the ARC function, along with the connection by an HDMI cable, connect the TV and this unit using a digital optical
cable.
( →p46)
No sound from a connected player
• Change the input selector on this unit to the position of the jack to which the player is connected.
• Check the digital audio output setting on the connected device. On some game consoles, such as those supporting DVD, the default setting may
be o.
• For some DVD-Video discs, you need to select an audio output format from a menu.
A speaker produces no sound
• Make sure that the polarity (+/-) of the speaker cables is correct, and that no bare wires are in contact with the metal part of speaker terminals.
• Make sure that the speaker cables are not shorting out.
• Check "Connect the Speaker Cables" ( →p31) to see if the speaker connections have been made correctly. Settings for the speaker
connection environment need to be made in "Speaker Setup" in Initial Setup. Check "Initial Setup with Auto Start-up Wizard" ( →p117).
• Depending on the input signal and listening mode, not much sound may be output from speakers. Select another listening mode to see if sound
is output.
• If surround back speakers are installed, be sure to install surround speakers as well.
• A maximum of 5.1 c h playback is possible when Bi-Amping connection is used. Be sure to remove the jumper bar on the speakers when using
Bi-Amping connection.
( →p31)
The subwoofer produces no sound
If the setting of the front speakers is "Full Band", the low range elements will be output from the front speakers instead of from the subwoofer during
2 ch audio input of TV or music. To output the sound from the subwoofer, make one of the following settings.
1. Change the setting for the front speakers to a setting of crossover frequency value other than "Full Band".
The range below the specied frequency will be output from the subwoofer instead of from the front speakers. If your front speakers have a high
low-range reproduction capability, changing this setting is not recommended.
2. Change "Double Bass" to "On".
The low range elements of the front speakers will be output from both the front speakers and the subwoofer. Due to this, the bass sound may be
emphasized too much. In such a case, do not change the setting, or make the setting with the above option 1.
• For the setting details, refer to "2. Speaker" - "Crossover" on the Setup menu.
• If the input signals do not contain subwoofer audio elements (LFE), the subwoofer may produce no sound.
( →p97)
126
Troubleshooting
Noise can be heard
• Using cable ties to bundle audio pin cables, power cords, speaker cables, etc. may degrade the audio quality. Do not bundle the cords.
• An audio cable may be picking up interference. Change the position of the cables.
The beginning of audio received by an HDMI IN cannot be heard
• Since it takes longer to identify the format of an HDMI signal than it does for other digital audio signals, audio output may not start immediately.
Sound suddenly reduces
• When using the unit for extended periods with the temperature inside the unit exceeding a certain temperature, the volume may be reduced
automatically to protect the circuits.
Sound suddenly changes
• When "My Input Volume" is set, the volume is set for each input selector. Check "4. Source" - "My Input Volume" on the Setup menu ( →p103).
Listening Modes
• To enjoy digital surround playback in formats such as Dolby Digital, you need to make a connection for audio signals with an HDMI cable, digital
coaxial cable or digital optical cable. Also, audio output need to be set to Bitstream output on the connected Blu-ray Disc player, etc.
• Press on the remote controller several times to switch the display of the main unit, and you can check the input format.
Check the following if the problem persists after you have conrmed the above.
Cannot select a desired listening mode
• Depending on the connection status of the speaker, some listening modes may not be selected. Check "Speaker Layouts and Selectable
Listening Modes" "Speaker Layouts and Selectable Listening Modes" ( →p136) or "Input Formats and Selectable Listening Modes" ( →p141).
Cannot listen to the sound in Dolby TrueHD, Dolby Atmos or DTS-HD Master Audio format
• If the audio in Dolby TrueHD, Dolby Atmos or DTS-HD Master Audio format cannot be output correctly in the source format, set "BD video
supplementary sound" (or reencode, secondary sound, video additional audio, etc.) to "O" in the setting of a connected Blu-ray Disc player, etc.
After changing the setting, switch the listening mode to that for each source, and conrm.
127
Troubleshooting
About Dolby signals
• When surround back speakers are included in the speaker layout, and software that is recorded with the 5.1-channel Dolby audio format is
played, the surround channel audio may be output from the surround back speakers.
• Some Dolby Atmos audio format that is used on games, etc., may be recognized as "Multichannel PCM". If this occurs, check the rmware
updates for the game console.
About DTS signals
• With media that switches suddenly from DTS to PCM, PCM playback may not start immediately. In such a case, stop playback on the player side
for approx. 3 seconds or more. Then, resume playback. The playback will be performed normally.
• DTS playback may not be performed normally on some CD and LD players even if the player and this unit are digitally connected. If some
processing (e.g., output level adjustment, sampling frequency conversion, or frequency characteristic conversion) has been executed for the
DTS signal being output, this unit cannot recognize it as a genuine DTS signal, and noise may occur.
• While playing a DTS-compatible disc, if a pause or skip operation is performed on your player, noise may occur for a short period. This is not a
malfunction.
Video
• Conrm that the connection between the output jack on the connected device and the input jack on this unit is correct.
• Make sure that none of the connecting cables are bent, twisted, or damaged.
• When the TV image is blurry or unclear, the power cord or connection cables of the unit may have interfered. In such a case, keep distance
between TV antenna cable and cables of the unit.
• Check the switching of the input screen on the monitor side such as a TV.
Check the following if the problem persists after you have conrmed the above.
No image appears
• Change the input selector on this unit to the position of the jack to which the player is connected.
• While the Pure Audio listening mode is selected, only video signals input from the HDMI input jack can be output.
128
Troubleshooting
No image from a device connected to HDMI IN jack
• To display video from the connected player on the TV while the unit is in standby, you need to enable "5. Hardware" - "HDMI" - "HDMI Standby
Through" on the Setup menu. For details of the HDMI Standby Through function, check "5. Hardware" - "HDMI" on the Setup menu.
• To output video to a TV connected to the HDMI OUT SUB jack, press the Q button on the remote controller to display "Quick Menu" and select
"HDMI" - "HDMI Out", or press the HDMI MAIN/SUB button on the remote controller and select the HDMI OUT jack.
• Check if "Resolution Error" is displayed on the main unit display when video input via HDMI IN jack is not displayed. In this case, the TV does
not support the resolution of the video input from the player. Change the setting on the player.
• Normal operation with an HDMI-DVI adapter is not guaranteed. In addition, video signals output from a PC are not guaranteed.
• Try switching o the Deep Color function. To turn o the Deep Color function, simultaneously press the STRM BOX and ON/STANDBY
buttons on the main unit. While holding down STRM BOX, press ON/STANDBY repeatedly until "Deep Color:O" appears on the display. To
reactivate the Deep Color function, repeat the above described step until "Deep Color:On" is appeared on the display.
( →p105)
Images icker
• The output resolution of the player may not be compatible with the resolution of the TV. If the player is connected to this unit with an HDMI cable,
change the output resolution on the player. Also this may be solved by changing the screen mode on the TV.
Video and audio are out of synch
• Depending on the settings on your TV and connection environment, the video may be behind the audio. Press Q on the remote controller to
display "Quick Menu", select "HDMI" - "A/V Sync", and make the adjustment.
( →p65)
Linked operation
HDMI linked operation does not work with CEC-compliant devices, such as a TV
• In the Setup menu of the unit, set "5. Hardware" - "HDMI" - "HDMI CEC" to "On".
• It is also necessary to set HDMI linking on the CEC-compliant device. Check the instruction manual.
• When connecting a Sharp brand player or recorder to the HDMI IN jacks, set "5. Hardware" - "HDMI" - "HDMI Standby Through" to "Auto" on the
Setup menu.
( →p105)
129
Troubleshooting
Tuner
Poor reception or much noise
• Recheck the antenna connection.
• Move the antenna away from the speaker cord or power cord.
• Move the unit away from your TV or PC.
• Passing cars or airplanes in the vicinity can cause interference.
• If radio waves are blocked by concrete walls, etc., radio reception may be poor.
• Change the reception mode to mono ( →p60).
• When listening to an AM station, operating the remote controller may cause noise.
• FM reception may be clearer if you use the antenna jack on the wall used for the TV.
( →p51)
BLUETOOTH function
• Unplug and plug the power cord of the unit, or turn o and on the BLUETOOTH enabled device. Restart of the BLUETOOTH enabled device
may be eective.
• BLUETOOTH enabled devices must support the A2DP prole.
• Because a radio wave interference will occur, this unit may not be used near devices such as a microwave oven or cordless phone which use
the radio wave in the 2.4 GHz range.
• A metallic object near the unit can aect on the radio wave, and BLUETOOTH connection may not be possible.
Check the following if the problem persists after you have conrmed the above.
Cannot transmit from a Bluetooth wireless technology enabled device (PC, smartphone, etc.) to this
unit
• Check if the BLUETOOTH function of the BLUETOOTH enabled device is enabled.
Cannot connect a BLUETOOTH wireless technology enabled device (PC, smartphone, etc.) to this
unit
• Initialize the pairing information and perform pairing again.
Firstly delete all the pairing information saved on this unit. In the Setup menu, select "5. Hardware" - "Bluetooth" - "Bluetooth Receiver" - "Pairing
Information", then press ENTER while "Clear" is displayed.
Next, delete the pairing information of this unit that is saved on the BLUETOOTH wireless technology enabled device. For information on how to
clear the pairing information, refer to the BLUETOOTH enabled device's instruction manual.
Finally, perform pairing again. Refer to "Playing audio from BLUETOOTH wireless technology enabled devices with this unit" ( →p56) for
pairing instructions.
( →p110)
130
Troubleshooting
Cannot transmit from this unit to a Bluetooth wireless technology enabled device (wireless
headphones, etc.)
• Check that the "Bluetooth Transmitter" setting on this unit is set to either "On(Tx)" or "On(Main + Tx)". ( →p110)
Cannot connect this unit to a BLUETOOTH wireless technology enabled device (wireless
headphones, etc.)
• Check if the BLUETOOTH function of the BLUETOOTH enabled device is enabled.
• Initialize the pairing information and perform pairing again.
Firstly delete all the pairing information saved on this unit. In the Setup menu, select "5. Hardware" - "Bluetooth" - "Bluetooth Transmitter" -
"Pairing Information", then press ENTER while "Clear" is displayed.
Next, delete the pairing information of this unit that is saved on the BLUETOOTH wireless technology enabled device. For information on how to
clear the pairing information, refer to the BLUETOOTH enabled device's instruction manual.
Finally, perform pairing again. Refer to "Transmitting audio from this unit to BLUETOOTH wireless technology enabled devices" ( →p57) for
pairing instructions.
( →p111)
Music playback is unavailable on the unit even after successful BLUETOOTH connection
• If the volume setting on this unit or the Bluetooth wireless technology enabled device is low, audio may not be played. Check the volume setting
on this unit or the Bluetooth wireless technology enabled device.
• Some Bluetooth enabled devices may be equipped with a Send/Receive selector switch. Try switching the setting to suit the application the
device is being used for.
• Depending on the characteristics or specications of the BLUETOOTH enabled device, music may not be played back on this unit.
Sound is interrupted
• There maybe a problem with the BLUETOOTH enabled device. Check the information on a web page.
The audio quality is poor after connection with a BLUETOOTH enabled device
• The BLUETOOTH reception is poor. Move the BLUETOOTH enabled device closer to the unit, or remove any obstacle between the
BLUETOOTH enabled device and this unit.
131
Troubleshooting
Network function
• If you cannot select a network service, start up the network function to select it. It may take approx. one minute to start it up.
• When the NET indicator is blinking, this unit is not properly connected to the home network.
• Unplug and plug the power cords of this unit and the router, or restart the router.
• If the desired router is not displayed in the access point list, it may be set to hide SSID, or the ANY connection may be o. Change the setting
and try again.
Check the following if the problem persists after you have conrmed the above.
Cannot access the Internet radio
• In the case the service provider has terminated the service, the network service or contents may not be used on this unit.
• Check if your modem and router are properly connected, and they are both turned on.
• Check if the LAN side port on the router is properly connected to this unit.
• Check if connecting to Internet from other devices is possible. If it is not possible, turn o all devices connected to the network, wait for a while,
and then turn on the devices again.
• Depending on ISP, setting the proxy server is required.
• Check if the router and modem you are using are supported by your ISP.
Cannot access the network server
• This unit needs to be connected to the same router as the network server.
• This unit supports the Windows Media
®
Player 12 network servers, or NASes that support the home network function.
• Windows Media
®
Player may require some settings. Refer to "Music Server".
• When using a PC, only the music les registered in the library of Windows Media
®
Player can be played.
( →p83)
Sound is interrupted when playing music les on the network server
• Check if the network server meets the requirements for operation.
• When the PC is serving as the network server, quit application software other than the server software (Windows Media
®
Player 12, etc.).
• If the PC is downloading or copying large les, the playback sound may be interrupted.
132
Troubleshooting
USB storage device
USB storage device is not displayed
• Check if the USB storage device or USB cable is securely inserted to the USB port of the unit.
• Disconnect the USB storage device once from the unit, and then reconnect it.
• Performance of the hard disk that receive power from the USB port of the unit is not guaranteed.
• Depending on the type of content, the playback may not be performed normally. Check the types of supported le formats.
• Operations of USB storage devices equipped with security functions are not guaranteed.
( →p80)
Wireless LAN Network
• Unplug and plug the power cords of this unit and the wireless LAN router, check the power-on status of the wireless LAN router, or restart the
wireless LAN router.
Check the following if the problem persists after you have conrmed the above.
Cannot access wireless LAN network
• The wireless LAN router setting may be switched to Manual. Restore the setting to Auto.
• Try the manual set-up. The connection may succeed.
• When the wireless LAN router is in stealth mode (mode to hide SSID) or when the ANY connection is o, the SSID is not displayed. Change the
setting and try again.
• Check if the SSID and encryption settings (WEP, etc.) are correct. Match the network settings with the settings of this unit.
• Connection to an SSID that includes multi-byte characters is not supported. Set the SSID of the wireless LAN router using single-byte
alphanumeric characters only, and try again.
Connected to an SSID dierent from the selected SSID
• Some wireless LAN routers allow you to set multiple SSIDs for one unit. If connecting to such a router using the automatic setting button, you
may end up connecting to an SSID dierent from the SSID you want to connect to. If this occurs, use the connection method requiring you to
enter a password.
133
Troubleshooting
Playback sound is interrupted, or communication is not possible
• You may not receive radio waves due to poor radio wave conditions. Shorten the distance from the wireless LAN router, or remove obstacles to
improve visibility, and connect again. Install the unit away from microwave ovens or other access points. It is recommended to install the wireless
LAN router and the unit in the same room.
• If there is a metallic object near the unit, wireless LAN connection may not be possible because the metal aects the radio wave.
• When other wireless LAN devices are used near the unit, other symptoms may occur, such as interrupted playback and impossible
communication. You can avoid those problems by changing the channel of your wireless LAN router. For instructions on changing channels,
refer to the instruction manual supplied with your wireless LAN router.
• There may not be enough bandwidth available in wireless LAN. Use a wired LAN for connection.
ZONE B function
The audio of an externally connected AV component cannot be output to ZONE B.
• To output the audio to ZONE B, select "Audio" - "Zone B" on the Quick Menu, and set the audio output destination to "On (A+B)" or "On (B)" ( →p88)
Remote Controller
• Make sure that the batteries are inserted with the correct polarity.
• Insert new batteries. Do not mix dierent types of batteries, or old and new batteries.
• Make sure that the sensor of the main unit is not subjected to direct sunlight or inverter-type uorescent lights. Relocate it if necessary.
• If the main unit is installed in a rack or cabinet with colored-glass doors, or if the doors are closed, the remote controller may not work normally.
Display
The display does not light up
• When the Dimmer function is working, the display may go dim. Press the DIMMER button, and change the brightness level of the display.
• The display is turned o when the Pure Audio listening mode is selected.
( →p16)
134
Troubleshooting
Others
Strange noise can be heard from the unit
• If you have connected another device to the same outlet as this unit, strange noise may occur under the inuence of the device. If the symptom
is remedied by removing the power plug of the other device from the outlet, use dierent outlets for this unit and the device.
The message "Noise Error" appears during AccuEQ Room Calibration
• This can be caused by a malfunction in your speaker unit. Check the speaker output, etc.
The measurement results of AccuEQ Room Calibration show dierent distances to the speakers from
the actual ones
• Depending on the speakers you are using, some errors may occur in the measurement results. If this is the case, make the settings in
"2. Speaker" - "Distance" in the Setup menu.
( →p98)
The measurement results of AccuEQ Room Calibration show that the volume level of the subwoofer
has been corrected to the lower limit
• The volume level correction of the subwoofer may not have been completed. Lower the volume of the subwoofer before
AccuEQ Room Calibration measurement.
136
Appendix
Speaker Layouts and Selectable Listening Modes
See the following table for selectable listening modes for each speaker layout.
Speaker layout (ch)
Listening mode 2.1 3.1 4.1 5.1 6.1 7.1 2.1.2 3.1.2 4.1.2 5.1.2
DD (Dolby Audio - DD)
(*1) (*1) (*1) (*2) (*2) (*3) (*3) (*3)
DD+ (Dolby Audio - DD+)
(*1) (*1) (*1) (*1)(*2) (*1)(*2) (*1) (*1) (*1) (*1)
DTHD (Dolby Audio - TrueHD)
(*1) (*1) (*1) (*1)(*2) (*1)(*2) (*1) (*1) (*1) (*1)
Atmos
Atmos 2.0/2.1
Atmos 3.0/3.1
Atmos 4.0/4.1
Atmos 5.0/5.1
Atmos 6.0/6.1
Atmos 7.0/7.1
Atmos 2.0.2/2.1.2
Atmos 3.0.2/3.1.2
DSur (Dolby Audio - Surr)
DSur 2.0/2.1 (Dolby Audio - Surr)
DSur 3.0/3.1 (Dolby Audio - Surr)
DSur 4.0/4.1 (Dolby Audio - Surr)
DSur 5.0/5.1 (Dolby Audio - Surr)
DSur 6.0/6.1 (Dolby Audio - Surr)
DSur 7.0/7.1 (Dolby Audio - Surr)
DSur 2.0.2/2.1.2 (Dolby Audio - Surr)
DSur 3.0.2/3.1.2 (Dolby Audio - Surr)
138
Appendix
Speaker layout (ch)
Listening mode 2.1 3.1 4.1 5.1 6.1 7.1 2.1.2 3.1.2 4.1.2 5.1.2
Multich (Multichannel)
(*1) (*1) (*1) (*1) (*1) (*3) (*3) (*3)
DSD
(*1) (*1) (*1) (*4) (*4) (*3) (*3) (*3)
Pure Audio
(*1) (*1) (*1) (*1)(*2) (*1)(*2) (*1) (*1) (*1) (*1)
Direct
(*1) (*1) (*1) (*1)(*2) (*1)(*2) (*1) (*1) (*1) (*1)
Stereo
(*5) (*5) (*5) (*5) (*5) (*5) (*5) (*5) (*5)
Mono
(*5) (*5) (*5) (*5) (*5) (*5) (*5) (*5) (*5)
Orchestra
Unplugged
Studio-Mix
TV Logic
Game-RPG
Game-Action
Game-Rock
Game-Sports
AllCh Stereo
Mono Music
T-D (Theater-Dimensional)
(*5) (*6) (*5) (*6) (*5) (*6) (*5) (*6)
*1: Reproduced with the sound eld according to the number of channels of input signals.
*2: If 4.1ch or 5.1ch Dolby signals (DD, DD+, DTHD) are input, surround channel audio is output from the surround back speakers.
*3: Not output from height speakers.
*4: Not output from surround back speakers.
*5: Output only from front speakers.
*6: Output only from front speakers and center speaker.
139
Appendix
LISTENING MODE buttons and Selectable Listening Modes
Refer to the following table for the listening modes that can be selected with each listening mode button.
LISTENING MODE buttons
Listening mode MOVIE/TV MUSIC GAME
DD (Dolby Audio - DD)
DD+ (Dolby Audio - DD+)
DTHD (Dolby Audio - TrueHD)
Atmos
Atmos 2.0/2.1
Atmos 3.0/3.1
Atmos 4.0/4.1
Atmos 5.0/5.1
Atmos 6.0/6.1
Atmos 7.0/7.1
Atmos 2.0.2/2.1.2
Atmos 3.0.2/3.1.2
DSur (Dolby Audio - Surr)
DSur 2.0/2.1 (Dolby Audio - Surr)
DSur 3.0/3.1 (Dolby Audio - Surr)
DSur 4.0/4.1 (Dolby Audio - Surr)
DSur 5.0/5.1 (Dolby Audio - Surr)
DSur 6.0/6.1 (Dolby Audio - Surr)
DSur 7.0/7.1 (Dolby Audio - Surr)
DSur 2.0.2/2.1.2 (Dolby Audio - Surr)
DSur 3.0.2/3.1.2 (Dolby Audio - Surr)
LISTENING MODE buttons
Listening mode MOVIE/TV MUSIC GAME
DTS
ES Discrete (DTS-ES Discrete)
ES Matrix (DTS-ES Matrix)
DTS 96/24
DTS-HD HR (DTS-HD High Resolution)
DTS-HD Master (DTS-HD Master Audio)
DTS Express
DTS:X
DTS Neural:X
DTS Virtual:X
LISTENING MODE buttons
Listening mode MOVIE/TV MUSIC GAME
Multich (Multichannel)
PCM
DSD
Pure Audio
Direct
Stereo
Mono
141
Appendix
Input Formats and Selectable Listening Modes
You can select a variety of listening modes
according to the audio format of the signal to be
input.
• Selectable listening modes when headphones
are connected are Pure Audio, Mono, Direct, and
Stereo only
Listening mode
Input format
Pure Audio
Direct
Stereo
DD
(Dolby Audio
- DD) (*2)
DD+
(Dolby Audio
- DD+)
(*2)(*3)
DTHD
(Dolby
Audio -
TrueHD) (*2)
Atmos
(*12)
DSur
(Dolby Audio
- Surr)
(*12)
2-channel signal input
Analog / PCM
Music le / DSD (*1)
DD / DD+ / DTHD
DTS / DTS 96/24 / DTS Express / DTS-
HD HR / DTS-HD MSTR
(*13)
Multi-channel signal input
Multich PCM
DSD (*1)
DD
DD+
DTHD
ATMOS
DTS
DTS 96/24
DTS Express
DTS-HD HR
DTS-HD MSTR
DTS-ES Discrete
DTS-ES Matrix
DTS:X
142
Appendix
Listening mode
Input format
DTS (*2)
DTS 96/24
(*2)
DTS
Express
(*2)
DTS-HD HR
(DTS-HD High
Resolution)
(*2)
DTS-HD
Master (DTS-
HD Master
Audio) (*2)
ES Discrete
(DTS-ES
Discrete)
(*5)
ES Matrix
(DTS-ES
Matrix) (*5)
DTS:X
DTS
Neural:X
(*6)
DTS
Virtual:X
(*9) (*10)
2-channel signal input
Analog / PCM
Music le / DSD (*1)
DD / DD+ / DTHD
DTS / DTS 96/24 / DTS
Express / DTS-HD HR /
DTS-HD MSTR
Multi-channel signal input
Multich PCM
DSD (*1)
DD
DD+
DTHD
ATMOS
DTS
DTS 96/24
DTS Express
DTS-HD HR
DTS-HD MSTR
DTS-ES Discrete
(*4)
DTS-ES Matrix
(*4)
DTS:X
143
Appendix
Listening mode
Input format
PCM
(Multich
PCM) (*2)
DSD
(*2)(*11)
Mono
Orchestra/ Unplugged/
Studio-Mix/ TV Logic/ Game-
Action/ Game-Rock/Game-
RPG/ Game-Sports (*7)
AllCh
Stereo /
Mo n o M u si c
(*8)
T-D (Theater-
Dimensional)
(*9)
2-channel signal input
Analog / PCM
Music le / DSD (*1)
DD / DD+ / DTHD
DTS / DTS 96/24 / DTS
Express / DTS-HD HR /
DTS-HD MSTR
Multi-channel signal input
Multich PCM
DSD (*1)
DD
DD+
DTHD
ATMOS
DTS
DTS 96/24
DTS Express
DTS-HD HR
DTS-HD MSTR
DTS-ES Discrete
DTS-ES Matrix
DTS:X
144
Appendix
(*1) You cannot select any mode other than Pure Audio, Direct, Stereo, AllCh Stereo and Mono Music if the sampling rate is 5.6/11.2 MHz.
(*2) A center speaker or surround speakers need to be installed.
(*3) If the input source is Blu-ray Disc and the speaker layout is 5.1 ch or less, DD+ cannot be selected. Instead, the listening mode for DD can be selected.
(*4) This can only be selected when no surround back speaker is connected.
(*5) Surround back speakers need to be installed.
(*6) If the input format is any of the following and the number of channels is monaural, this listening mode becomes unavailable.
– DTS, DTS 96/24, DTS Express, DTS-HD HR, DTS-HD MSTR, PCM, music le
(*7) Surround speakers or height speakers need to be installed.
(*8) A center speaker, surround speakers, or height speakers need to be installed.
(*9) Cannot be selected if "Speaker Virtualizer" ( →p100) is set to "O".
(*10) Cannot be selected when height speakers are installed.
(*11) Cannot be selected when the input format is monaural.
(*12) The listening mode displayed depends on the speaker layout ( →p136). Furthermore, when the setting for "Speaker Virtualizer" ( →p100) is "O" (the default
value is On), then modes other than Atmos and DSur cannot be selected
(*13) This cannot be selected when the input format is DTS Express.
Speaker Layouts and Selectable Listening
Modes ( →p136)
145
Appendix
Listening Mode Eects
In alphabetical order
AllCh Stereo
This mode is ideal for background music. Stereo sound is played through the
surround speakers as well as the front speakers, creating a stereo image.
Atmos
Since this mode calculates the positional data of audio recorded in Dolby Atmos
audio in real-time and outputs it from appropriate speakers, you can enjoy the
natural and stereophonic sound eld of Dolby Atmos with any speaker layout
including connection of only front speakers. Also, the Dolby Atmos sound design
can be reproduced more faithfully by connecting surround back speakers or
height speakers. You can select this mode when inputting the Dolby Atmos
audio format.
Unlike existing surround systems, Dolby Atmos does not rely on channels, but
rather enables the accurate placement of sound objects that have independent
motion in a 3D space with even greater clarity. Dolby Atmos is an optional
audio format for Blu-ray Discs and achieves a more stereophonic sound eld by
introducing a sound eld above the listener.
According to the speaker layout, the following listening modes are displayed.
– Atmos 2.0/2.1: When only front speakers are installed
– Atmos 3.0/3.1: When front speakers and center speaker are installed
– Atmos 4.0/4.1: When front speakers and surround speakers are
installed
– Atmos 5.0/5.1: When front speakers, center speaker and surround
speakers are installed
– Atmos 6.0/6.1: When front speakers, surround speakers and surround
back speakers are installed
– Atmo s 7.0 / 7.1: When front speakers, center speaker, surround speakers
and surround back speakers are installed
– Atmos 2.0.2/2.1.2: When front speakers and height speakers are
installed
– Atmos 3.0.2/3.1.2: When front speakers, center speaker and height
speakers are installed
– Atmos: Selectable in the "4.1.2 ch" or "5.1.2 ch" setting with surround
speakers and height speakers installed.
• To enable transfer of this audio format, connect via an HDMI cable and set
the audio output on the player to Bitstream output.
• When "Speaker Virtualizer" ( →p100) is set to "O" (Default: On), modes
other than Atmos cannot be selected.
DD (Dolby Audio - DD)
This mode faithfully reproduces the sound design recorded in the Dolby Digital
audio format.
Dolby Digital is a multi-channel digital format developed by Dolby Laboratories,
Inc. and is widely adopted for use in movie production. It is also a standard audio
format for DVD-Video and Blu-ray Discs. It is possible to record a maximum of
5.1 channels on a DVD-Video or Blu-ray Disc; two front channels, one center
channel, two surround channels, and the LFE channel dedicated to the bass
region (sound elements for the subwoofer).
• To enable transfer of this audio format, connect via a digital cable and set the
audio output on the player to Bitstream output.
DD+ (Dolby Audio - DD+)
This mode faithfully reproduces the sound design recorded in the Dolby Digital
Plus audio format.
The Dolby Digital Plus format has been improved based on Dolby Digital,
increasing the number of channels and endeavoring to improve sound quality
by giving more exibility in data bit rates. Dolby Digital Plus is an optional audio
format based on 5.1 ch for Blu-ray Discs. It is possible to record a maximum of
7.1 channels with additional channels such as the surround back channel.
• To enable transfer of this audio format, connect via an HDMI cable and set
the audio output on the player to Bitstream output.
146
Appendix
Direct
This listening mode can be selected for all input signals. Processing that aects
sound quality is shut down, and sound closer to the original is reproduced. The
sound is reproduced with the sound eld based on the number of channels
in the input signal. For example, a 2 ch signal is output only from the front
speakers.
Note that the sound adjustment is not available when this mode is selected.
DSur (Dolby Audio - Surr)
This listening mode expands 2 ch or 5.1 ch input signals to 5.1 ch, 7.1 ch or
5.1.2 ch. This mode expands actual channels to more channels for playback
according to the conguration of the connected speakers. Also, even if there is
no speaker for expansion, for example when only front speakers are connected,
audio of surround channel or height channel is virtually created for expansion
playback.
According to the speaker layout, the following listening modes are displayed.
–
DSur 2.0/2.1: When only front speakers are installed
–
DSur 3.0/3.1: When front speakers and center speaker are installed
– DSur 4.0/4.1: When front speakers and surround speakers are installed
–
DSur 5.0/5.1: When front speakers, center speaker and surround
speakers are installed
– DSur 6.0/6.1: When front speakers, surround speakers and surround
back speakers are installed
–
DSur 7. 0 / 7.1: When front speakers, center speaker, surround speakers
and surround back speakers are installed
– DSur 2.0.2/2.1.2: When front speakers and height speakers are
installed
–
DSur 3.0.2/3.1.2: When front speakers, center speaker and height
speakers are installed
–
DSur: Selectable in the "4.1.2 ch" or "5.1.2 ch" setting with surround
speakers and height speakers installed.
• When "Speaker Virtualizer" ( →p100) is set to "O" (Default: On), modes
other than DSur cannot be selected.
DTHD (Dolby Audio - TrueHD)
This mode faithfully reproduces the sound design recorded in the Dolby TrueHD
audio format.
The Dolby TrueHD audio format is a "lossless" format expanded based on the
lossless compression technology referred to as MLP, and it faithfully reproduces
the master audio recorded in the studio. Dolby TrueHD is an optional audio
format based on 5.1 ch for Blu-ray Discs. It is possible to record a maximum of
7.1 channels with additional channels such as the surround back channel. 7.1 ch
is recorded at 96 kHz/24 bit, and 5.1 ch is recorded at 192 kHz/24 bit.
• To enable transfer of this audio format, connect via an HDMI cable and set
the audio output on the player to Bitstream output.
DSD
This mode is suitable for playing sources recorded in DSD.
• This unit supports the DSD signal input from the HDMI input terminal.
However, depending on the connected player, better sound may be obtained
by setting the output on the player side to the PCM output.
• This listening mode cannot be selected if the output setting on your Blu-ray
Disc/DVD player is not set to DSD.
DTS
This mode faithfully reproduces the sound design recorded in the DTS audio
format.
The DTS audio format is a multi-channel digital format developed by DTS, Inc.
This format is an optional audio format for DVD-Video and a standard format
for Blu-ray Discs. It enables recording of 5.1 channels; two front channels, one
center channel, two surround channels, and the LFE channel dedicated to the
bass region (sound elements for the subwoofer). The content is recorded with a
rich volume of data, with a maximum sampling rate of 48 kHz, at a resolution of
24 bits and a bit rate of 1.5 Mbps.
• To enable transfer of this audio format, connect via a digital cable and set the
audio output on the player to Bitstream output.
147
Appendix
DTS 96/24
This mode faithfully reproduces the sound design recorded in the DTS 96/24
audio format.
The DTS 96/24 format is an optional audio format for DVD-Video and Blu-ray
Discs. It enables recording of 5.1 channels; two front channels, one center
channel, two surround channels, and the LFE channel dedicated to the bass
region (sound elements for the subwoofer). Detailed reproduction is achieved by
recording the content at a sampling rate of 96 kHz and at a resolution of 24 bits.
• To enable transfer of this audio format, connect via a digital cable and set the
audio output on the player to Bitstream output.
DTS Express
This mode faithfully reproduces the sound design recorded in the DTS Express
audio format.
DTS Express is an optional audio format based on 5.1 ch for Blu-ray Discs. It is
possible to record a maximum of 7.1 channels with additional channels such as
the surround back channel. It also supports low bit rates.
• To enable transfer of this audio format, connect via an HDMI cable and set
the audio output on the player to Bitstream output.
DTS-HD HR (DTS-HD High Resolution)
This mode faithfully reproduces the sound design recorded in the DTS-HD High
Resolution Audio audio format.
DTS-HD High Resolution Audio is an optional audio format based on 5.1 ch for
Blu-ray Discs. It is possible to record a maximum of 7.1 channels with additional
channels such as the surround back channel at a sampling rate of 96 kHz and at
a resolution of 24 bits.
• To enable transfer of this audio format, connect via an HDMI cable and set
the audio output on the player to Bitstream output.
DTS-HD MSTR (DTS-HD Master Audio)
This mode faithfully reproduces the sound design recorded in the DTS-HD
Master Audio audio format.
DTS-HD Master Audio is an optional audio format based on 5.1 ch for Blu-
ray Discs. It is possible to record a maximum of 7.1 channels with additional
channels such as the surround back channel using the lossless audio
reproduction technology. 96 kHz/24 bit is supported for 7.1 ch, and 192 kHz/24
bit is supported for 5.1 ch.
• To enable transfer of this audio format, connect via an HDMI cable and set
the audio output on the player to Bitstream output.
DTS Neural:X
This listening mode expands actual channels to more channels for playback to
suit the conguration of the connected speakers by expanding the input signals
from 2 channels or 5.1 channels to 5.1 channels or 7.1 channels respectively.
DTS Virtual:X
DTS Virtual:X listening mode uses the proprietary audio processing technology
to create spacious 3D sound including audio from up above without connecting
height speakers.
This mode can be selected in any speaker layout such as front speakers-only
connection. You can enjoy your favorite movies or TV programs with a more
immersive audio experience.
• This mode cannot be selected when height speakers are connected.
• This mode cannot be selected when "Speaker Virtualizer" ( →p100) is set to
"O" (Default: On).
DTS:X
This mode faithfully reproduces the sound design recorded in the DTS:X audio
format.
The DTS:X audio format is a combination of the mixing method based on
traditional channel based formats (5.1 ch and 7.1 ch) and object based dynamic
audio mixing, and it is characterized by the precise positioning of sounds and the
ability to express sound movement.
• To enable transfer of this audio format, connect via an HDMI cable and set
the audio output on the player to Bitstream output.
148
Appendix
ES Discrete (DTS-ES Discrete)
This mode faithfully reproduces the sound design recorded in the DTS-ES
Discrete audio format.
DTS-ES Discrete is an optional audio format based on 5.1 ch for DVD-Video
and Blu-ray Discs. It is possible to record a maximum of 6.1 channels with a
monaural surround back channel added.
• To enable transfer of this audio format, connect via a digital cable and set the
audio output on the player to Bitstream output.
ES Matrix (DTS-ES Matrix)
This mode faithfully reproduces the sound design recorded in the DTS-ES
Matrix audio format.
DTS-ES Matrix is an optional audio format based on 5.1 ch for DVD-Video and
Blu-ray Discs. A monaural surround back channel is inserted to this format by
matrix encoding. During playback, 6.1 channel-playback is achieved by the
matrix decoder on this unit.
• To enable transfer of this audio format, connect via a digital cable and set the
audio output on the player to Bitstream output.
Game-Action
This mode is suitable for games with a lot of action.
Game-Rock
This mode is suitable for games with rock content.
Game-RPG
This mode is suitable for role-playing games.
Game-Sports
This mode is suitable for sports games.
Mono
In this mode, monaural audio is played from the center speaker at the time
of inputting an analog signal or PCM signal. If there is no center speaker
connected, monaural audio is played from the front speakers.
Mono Music
In this mode, all speakers output the same sound in mono, so the sound you
hear is the same regardless of where you are within the listening room.
Multich (Multichannel)
This mode is suitable to play sources recorded in multichannel PCM.
Orchestra
This mode is suitable for classical or operatic music. This mode emphasizes the
surround channels in order to widen the sound image, and simulates the natural
reverberation of a large hall.
Pure Audio
This mode reproduces the original sound more faithfully. The display is turned
o to provide purer sound.
Note that the sound adjustment is not available when this mode is selected.
Stereo
In this mode, sound is output from the right and left front speakers and
subwoofer.
Studio-Mix
This mode is suitable for rock or pop music. This mode creates a lively sound
eld with a powerful acoustic image as if you are at a club or rock concert.
149
Appendix
T-D (Theater-Dimensional)
In this mode, you can enjoy a virtual playback of multichannel surround sound
even with only two or three speakers. This works by controlling how sounds
reach the listener’s left and right ears.
• This mode cannot be selected when "Speaker Virtualizer" ( →p100) is set to
"O" (Default: On).
TV Logic
Suitable for TV shows produced in a TV studio. This mode gives clarity to voices
by enhancing the entire surround sounds, and creates a realistic acoustic image.
Unplugged
Suitable for acoustic instruments, vocals and jazz. This mode emphasizes the
front sound eld image, giving the impression of being in front of the stage.
150
Appendix
Speaker combinations
• Up to two powered subwoofers can be connected in either combination.
Speaker Channels FRONT CENTER SURROUND
SURROUND
BACK
HEIGHT Bi-AMP
ZONE B
(ZONE SPEAKER)
2.1 ch
(*1) (*1)
3.1 ch
(*1) (*1)
4.1 c h
(*1) (*1)
5.1 ch
(*1) (*1)
6.1 ch
7.1 ch
2.1.2 c h
(*2) (*1) (*2) (*1)
3.1.2 c h
(*2) (*1) (*2) (*1)
4.1. 2 ch
5.1.2 c h
(*1) You can select either Bi-AMP or ZONE SPEAKER.
(*2) When using Bi-Amp speakers, connect the Bi-Amp speakers to the HEIGHT terminals and connect the height speakers to the SURROUND terminals.
151
Appendix
General Specications
Amplier Section
Rated Output Power
With 8 ohm loads, both channels driven, from 20-20,000 Hz; rated 80 watts per channel minimum RMS power,
with no more than 0.08% total harmonic distortion from 250 milliwatts to rated output. (FTC)
Maximum Eective Output Power 165 W at 6 ohms, 1 kHz, 1 ch driven of 10% THD
Dynamic Power (IEC60268-Short-term
maximum output power)
160 W (3 Ω, Front), 125 W (4 Ω, Front), 85 W (8 Ω, Front)
THD+N (Total Harmonic Distortion + Noise) 0.08% (20 Hz - 20,000 Hz, Rated output power)
Input Sensitivity and Impedance 200 mV/32 kΩ (LINE(RCA))
Rated RCA Output Level and Impedance
PRE OUT (SUBWOOFER) : 1 V/470 Ω
PRE/LINE OUT (ZONE B) : 200 mV/2.2 kΩ
Frequency Response 10 Hz - 100 kHz/+1 dB, –3 dB (Direct/Pure Audio)
Tone Control Characteristics ±10 dB, 20 Hz (BASS), ±10 dB, 20 kHz (TREBLE)
Signal to Noise Ratio 106 dB (IHF-A, LINE IN, SP OUT)
Speaker Impedance 4 Ω - 16 Ω
Headphone Rated Output 80 mW + 80 mW (32 Ω, 1 kHz, 10% THD)
Supported impedance of Headphones 8 Ω - 600 Ω
Headphones Frequency Response 10 Hz - 100 kHz
152
Appendix
Tuner Section
FM Tuning Frequency Range 87.5 MHz - 107.9 MHz
50 dB quieting sensitivity (FM MONO) 1.0 μV, 11.2 dBf (IHF, 1 kHz, 100% MOD)
AM Tuning Frequency Range 530 kHz - 1710 kHz
Preset Channel 40
BLUETOOTH Section
Communication system BLUETOOTH Specication version 4.2
Frequency band 2.4 GHz band
Modulation method FHSS (Frequency Hopping Spread Spectrum)
Compatible BLUETOOTH proles A2DP 1.2, AVRCP 1.3
Supported Codecs
Receiving: SBC, AAC
Transmitting: SBC, aptX, aptX HD
Transmission range (A2DP) 20 Hz - 20 kHz (Sampling frequency 44.1 kHz)
Maximum communication range
Line of sight approx. 15 m(*)
(*)The actual range will vary depending on factors such as obstacles between devices, magnetic elds around
a microwave oven, static electricity, cordless phone, reception sensitivity, antenna's performance, operating
system, software application, etc.
153
Appendix
HDMI
Input 4
Output 2 (MAIN, SUB)
Input *1 Output
HDMI 1 HDMI 2 HDMI 3 HDMI 4 MAIN SUB
HDMI Ver 2.1 2.1 2.1 2.1 2.1 2.1
bandwidth 24Gbps 24Gbps 24Gbps 24Gbps 24Gbps 24Gbps
ALLM
VRR (for Game)
QMS (for Movie)
FVA (for Game)
QFT (for Movie)
DSC
Uncompressed 8K/24p
4:2:0
8K/24p
4:2:0
8K/24p
4:2:0
8K/24p
4:2:0
8K/24p
4:2:0
8K/24p
4:2:0
Compressed
(TV needs DSC)
8K/60p
4:4:4
8K/60p
4:4:4
8K/60p
4:4:4
8K/60p
4:4:4
8K/60p
4:4:4
8K/60p
4:4:4
ARC / eARC *2
HDR10 (HDR10,
BT.2020, HLG)
HDR10+
*1 Audio Format: 2 ch linear PCM (32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz, 16/20/24 bit)
Multi-channel linear PCM (Maximum 7.1 channels, 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz, 16/20/24 bit)
Bitstream (Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS, DTS-ES, DTS 96/24, DTS-HD Master Audio,
DTS-HD High Resolution Audio, DTS Express, DTS:X, DSD(2.8 MHz), PCM)
*2
ARC compatible audio formats
: PCM, Dolby Digital, Dolby Digital Plus, DTS (DTS 96/24, DTS-ES, etc.), DTS-HD High Resolution Audio
eARC compatible audio formats
: PCM, Dolby Digital, Dolby Digital Plus, DTS (DTS 96/24, DTS-ES, etc.), Dolby TrueHD, Dolby Atmos, DTS- HD Master Audio,
DTS:X, Multichannel PCM, DTS-HD High Resolution Audio
154
Appendix
Supported input
resolutions
Frame rate Color space Color depth HDMI IN 1 - 3 HDMI IN 4 - 6
AUX INPUT HDMI
(Front)
4K
(3840x2160p)
4K SMPTE
(4096x2160p)
24/25/30 Hz YCbCr4:2:2 12 bit
YCbCr4:4:4/RGB 8 bit
10/12 bit
48/50/60 Hz YCbCr4:2:0 8 bit
10/12 bit
YCbCr4:2:2 12 bit
YCbCr4:4:4/RGB 8 bit
10/12 bit
100/120 Hz YCbCr4:2:0 8/10/12 bit
YCbCr4:2:2 12 bit
(*1)
YCbCr4:4:4/RGB 8/10 bit
(*1)
12 bit
(*1) (*1)
5K
(5120x2160p)
24/25/30 Hz YCbCr4:2:2 12 bit
YCbCr4:4:4/RGB 8 bit
10/12 bit
48/50/60 Hz YCbCr4:2:0 8/10/12 bit
(*2) (*2)
YCbCr4:2:2 12 bit
YCbCr4:4:4/RGB 8 bit
10/12 bit
(*1)
8K
(7680x4320p)
24/25/30 Hz YCbCr4:2:0 8/10/12 bit
YCbCr4:2:2 12 bit
(*1)
YCbCr4:4:4/RGB 8/10 bit
(*1)
12 bit
(*1) (*1)
48/50/60 Hz YCbCr4:2:0 8/10 bit
(*1)
12 bit
(*1) (*1)
YCbCr4:2:2 12 bit
(*1) (*1)
YCbCr4:4:4/RGB 8/10/12 bit
(*1) (*1)
(*1) Video compressed with DSC (Display Stream Compression) can be input and output. DSC is a video compression technique that enables the transmission of
high-resolution video, which requires high bandwidth, via HDMI.
(*2)5K, 48Hz, YCbCr4:2:0, 8/10/12 bit is not supported.
155
Appendix
• Signals are output from the HDMI OUT jack of this unit to the TV with the same resolution as the input resolution. When a TV supporting 4K is used, HDMI video
signals with 1080p can be output with 4K.
For linked functions to work properly, do not connect CEC-compliant devices exceeding the connectable number to the HDMI jack as shown below.
• Blu-ray Disc/DVD players: up to 3 units
• Blu-ray Disc/DVD recorders: up to 3 units
• Cable TV tuner, terrestrial digital tuner, and satellite broadcasting tuner: up to 4 units
Operation has been conrmed on the following devices: (As of April 2020)
Toshiba brand televisions; Sharp brand televisions; Onkyo and Integra brand RIHD-compatible players; Toshiba brand players and recorders; Sharp brand players
and recorders (when used with a Sharp brand television)
Network Section
Ethernet LAN 1 (10BASE-T/100BASE-TX)
Wireless LAN IEEE 802.11 a/b/g/n/ac standard (Wi-Fi
®
standard) 5 GHz/2.4 GHz band
■ Music Server ( →p83)
Supported Audio Formats
MP3 (.mp3)
• MPEG-1/MPEG-2 Audio Layer-3/44.1 kHz, 48 kHz/Between 8 kbps and 320 kbps, and VBR
WMA (.wma)
• 44.1 kHz, 48 kHz/Between 5 kbps and 320 kbps, and VBR
• WMA Pro/Voice/WMA Lossless formats are not supported.
WAV (.wav)
WAV les contain uncompressed PCM digital audio.
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
AIFF (.ai/.aif)
AIFF les contain uncompressed PCM digital audio.
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
AAC (.aac/.m4a/.mp4/.3gp/.3g2)
• MPEG-2/MPEG-4 Audio/44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/Between 8 kbps and 320 kbps, and VBR
FLAC (.ac)
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
LPCM (Linear PCM)
• 44.1 kHz, 48 kHz/16 bit
Apple Lossless (.m4a/.mp4)
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/16 bit, 24 bit
DSD (.dsf/.d)
• DSF/DSDIFF/2.8 MHz, 5.6 MHz, 11.2 MHz
156
Appendix
USB Section
USB 1 (Rear : Ver.2.0, 5V/1 A)
■ USB Storage Device ( →p80)
Supported Audio Formats
MP3 (.mp3)
• MPEG-1/MPEG-2 Audio Layer-3/44.1 kHz, 48 kHz/Between 8 kbps and 320 kbps, and VBR
WMA (.wma)
• 44.1 kHz, 48 kHz/Between 5 kbps and 320 kbps, and VBR
• WMA Pro/Voice/WMA Lossless formats are not supported.
WAV (.wav)
WAV les contain uncompressed PCM digital audio.
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
AIFF (.ai/.aif)
AIFF les contain uncompressed PCM digital audio.
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
AAC (.aac/.m4a/.mp4/.3gp/.3g2)
• MPEG-2/MPEG-4 Audio/44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz/Between 8 kbps and 320 kbps, and VBR
FLAC (.ac)
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/8 bit, 16 bit, 24 bit
LPCM (Linear PCM)
• 44.1 kHz, 48 kHz/16 bit
Apple Lossless (.m4a/.mp4)
• 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz/16 bit, 24 bit
DSD (.dsf/.d)
• DSF/DSDIFF/2.8 MHz, 5.6 MHz, 11.2 MHz
General
Power Supply AC 120 V, 60 Hz
Power Consumption 490 W
Full Standby mode 0.10 W
Network Standby (wired) 1.6 W
Network Standby (wireless) 1.7 W
Bluetooth Wakeup 1.6 W
HDMI CEC 0.1 W
157
Appendix
Standby mode (ALL ON) 1.7 W
Equipment with HiNA functionality Standby
mode, Network disconnect and Network
Standby ON
2.6 W
This equipment complies with European Commission Regulation (EC) No 1275/2008 as equipment with HiNA
functionality. If you do not to use the Network function, please set Network Standby setting to O. You can
reduce power consumption under standby mode.
Dimensions (W × H × D)
435 mm × 160 mm × 327.8 mm
17-1/8" × 6-5/16" × 12-7/8"
Weight 8.4 kg (18.5 lbs.)
Video Section
Composite None
Component None
Audio Inputs
Analog 3
Digital 2 (COAXIAL × 1, OPTICAL × 1)
158
Appendix
Audio Outputs
Analog
PRE/LINE OUT (ZONE B) × 1
PRE OUT (SUBWOOFER) × 2
Speaker Outputs
7 (FRONT L/R, CENTER, SURROUND L/R, HEIGHT L/R or SURROUND BACK L/R or ZONE B L/R)
• FRONT L/R terminals support banana plugs.
Phones 1 (ø 6.3 mm, 1/4")
Others
Setup Mic 1 (Front)
RS-232 None
12V TRIGGER OUT None
IR None
Specications and features are subject to change without notice.
License and Trademark
